Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

Mobile Device Security Using Transient Authentication

Mobile devices are vulnerable to theft and loss due to their small size and the characteristics of their common usage environment. Since they allow users to work while away from their desk, they are most useful in public locations and while traveling. Unfortunately, this is also where they are most at risk. Existing schemes for securing data either do not protect the device after it is stolen or require bothersome reauthentication. Transient Authentication lifts the burden of authentication from the user by use of a wearable token that constantly attests to the user's presence. When the user departs, the token and device lose contact and the device secures itself. We show how to leverage this authentication framework to secure all the memory and storage locations on a device into which secrets may creep. Our evaluation shows this is done without inconveniencing the user, while imposing a minimal performance overhead     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.     

Modeling aviation baggage screening security systems: a case study

Aviation security protects vital national interests, as well as passengers and aircraft. Key components of an aviation security system include baggage and passenger screening devices and operations. Determining how and where to assign (deploy) such devices can be quite challenging. Moreover, even after such systems are in place, it can be difficult to measure their effectiveness. This paper describes how discrete optimization models can be used to address these questions, based on three performance measures that quantify the effectiveness of airport baggage screening security device systems. These models are used to solve for optimal airport baggage screening security device deployments considering the number of passengers on a set of flights who have not been cleared using a security risk assessment system in use by the Federal Aviation Administration (i.e., passengers whose baggage is subjected to screening), the number of flights in this set, and the size of the aircraft for such flights. Several examples are provided to illustrate these results, including an example that uses data available from the Official Airline Guide.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.