High-gain pseudomorphic InGaAs base ballistic hot-electron device

A high-gain ballistic hot-electron device is described. The GaAs-AlGaAs heterostructure device, with a 21-mm-thick pseudomorphic In _0.12Ga_0.88As base, had a current gain of 27 at 77 K and 41 at 4.2 K. As characteristically seen in ballistic devices, transfer into the L valley limited the maximum gain. The Γ-L valley separation in the strained In_0.12Ga_0.88As was estimated to be about 380 meV     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Arc root mobility on piezoelectrically actuated contacts in miniature circuit breakers

A novel contact opening mechanism has been developed using a piezoelectric actuator to open the contacts in a low contact opening velocity circuit breaker. The arc control on the contacts is critical for successful current interruption (10/sup 3/-10/sup 4/ A) in low voltage (<250V) devices. Previous work has shown how arc root commutation from the contact region into the arc chamber is affected by arc chamber materials, contact materials and the gap behind the moving contact for contact velocities between 1ms/sup -1/ and 10ms/sup -1/. This work is extended using a commercially available piezoelectric actuator to open the contacts. Contact opening speeds are assessed and the arc root mobility is characterized under this operating regime. A flexible test apparatus and solid-state high-speed arc imaging system are used to gather data on the arc root during the opening of the contacts. New experimental results are presented on the anode and cathode root velocity and arc root motion in an arc chamber with piezoelectrically actuated contact opening. These results can be used to improve the design of high current low voltage circuit breakers suitable for piezoelectric actuation.     

High performance biofilm process for treating wastewater discharged from coal refining plants containing nitrogen, cyanide and thiocyanate.

Wastewater discharge from coal refining plants contains a number of biologically toxic compounds; 2000-2500 mg/l of COD of which 40% is composed of phenol, 100-400 mg/l of thiocyanate, 10-40 mg/l of cyanide, 100-250 mg/l of NH4+-N and 150-300 mg/l of total nitrogen. In order to treat this kind of high strength wastewater, we have developed a high performance biofilm process using fluidizing bio-carriers of the tube chip type. The fluidizing biofilm carriers are made of a composite of polyethylene and several inorganic materials, whose density is controlled at 0.97-0.98 g/ml. The fluidizing biofilm carriers show sound fluidization characteristics inside bioreactors. The wastewater is treated using three consecutive series reactors in oxic-anoxic-oxic arrangement. Each reactor is charged with the fluidizing biofilm carriers of 50 vol%. Furthermore, newly cultured active microorganisms for the thiocyanate biodegradation are added in the biofilm process. At total hydraulic retention time of 2.2 days, this process can achieve steady state removal efficiencies: COD, 99%; thiocyanate, 99%; NH4+-N, 99% and total nitrogen, 90%.     

Optical characteristics of waste stabilization ponds: recommendations for monitoring.

The optical character of waste stabilization ponds (WSPs) is of concern for several reasons. Algal photosynthesis, which produces oxygen for waste oxidation in WSPs, is influenced by attenuation of sunlight in ponds. Disinfection in WSPs is influenced by optical characteristics because solar UV exposure usually dominates inactivation. The optical nature of WSPs effluent also affects assimilation by receiving waters. Despite the importance of light behaviour in WSPs, few studies have been made of their optical characteristics. We discuss simple optical measures suitable for routine monitoring of WSPs (including at sites remote from laboratories): optical density of filtrates - an index of dissolved coloured organic (humic) matter, visual clarity - to provide an estimate of the beam attenuation coefficient (a fundamental quantity needed for optical modelling) colour (hue) - as an indicator of general WSP 'condition' and irradiance attenuation quantifying depth of light penetration. The value of optical characterisation of WSPs is illustrated with reference to optical data for WSPs in NZ (including high-rate algal ponds) treating dairy cattle wastewater versus domestic sewage. We encourage increased research on optical characteristics of WSPs and the incorporation of optical measures in monitoring and modelling of WSP performance.     

The impact of new product development acceleration approaches on speed and profitability: lessons for pioneers and fast followers

This work investigates the impact of nine new product development (NPD) acceleration approaches (supplier involvement, lead user involvement, speeding up activities and tasks, reduction of parts and components, training and rewarding of employees, implementation of support systems and techniques, stimulating interfunctional cooperation, emphasis on the customer, and simplification of organizational structure) on development speed and new product profitability. Our findings from 233 manufacturing firms show that lead user involvement and training/rewarding of employees increase both development speed and profitability. Supplier involvement, speeding up activities and tasks, and a simplification of the organizational structure also enhance development speed, while an emphasis on the customer has an additional positive impact on new product profitability. Both new product speed and profitability increase firm financial performance. Our results further show that pioneers and fast followers should not select the same NPD acceleration approaches as the speed and profitability impact of the majority of the acceleration approaches depends on the new product strategy of the firm. These results are important as they provide guidance for pioneers and fast followers regarding which NPD acceleration approaches to select in order to enhance speed and profitability and, hence, firm financial performance.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Computerized conferencing for knowledge acquisition from multiple experts

The increasing complecity of many expert system application areas calls for the integration of the knowledge of multiple experts. The use of multiple experts introduces some interesting new problems during the process of knowledge acquisition. The problems are further complicated when the experts are geographically dispersed or unavailable for face-to-face interactions.

This article discusses the motivations for acquiring the knowledge of multiple experts, the problems related to knowledge acquisition, new issues that arise whens multiple experts interact, solutions that can be brought to bear in building multiple expert systems (particularly when experts are geographically dispersed), and new tools for knowledge engineers to use when dealing with multiple experts.     

The application of SSADM to modelling the logical structure of proteins.

A logical design that describes the overall structure of proteins, together with a more detailed design describing secondary and some supersecondary structures, has been constructed using the computer-aided software engineering (CASE) tool, Auto-mate. Auto-mate embodies the philosophy of the Structured Systems Analysis and Design Method (SSADM) which enables the logical design of computer systems. Our design will facilitate the building of large information systems, such as databases and knowledgebases in the field of protein structure, by the derivation of system requirements from our logical model prior to producing the final physical system. In addition, the study has highlighted the ease of employing SSADM as a formalism in which to conduct the transferral of concepts from an expert into a design for a knowledge-based system that can be implemented on a computer (the knowledge-engineering exercise). It has been demonstrated how SSADM techniques may be extended for the purpose of modelling the constituent Prolog rules. This facilitates the integration of the logical system design model with the derived knowledge-based system.