Industrial TiO2 based nacreous pigments as functional building materials: Photocatalytic removal of NO

In this paper, the photocatalytic activity of industrial titanium dioxide (TiO₂) based nacreous pigments was researched as functional building materials for photocatalytic NO remove. Three industrial TiO₂ based nacreous pigments were selected to estimate the photocatalytic activity for NO remove. This study is a good proof that pearlescent pigments can eliminate NO, and its performance is positively correlated with its titanium dioxide content. And this research will widen the application of nacreous pigments in functional building materials, and provide a new way to eliminate in door nitric oxide pollution.     

Quantitative Analysis of Zinc Vaporization from Manganese Zinc Ferrites

Zinc vaporization of Mn-Zn ferrites was quantitatively characterized in terms of oxygen partial pressure P _O2, temperature, grain size and sample geometry. The amount of zinc loss was measured as a function of time at various temperatures by a thermogravimetric method. The weight loss due to irreversible zinc vaporization showed a linear behavior with time and increased exponentially with temperature. The observed weight loss due to zinc evaporation at 1100°C was small, whereas a significant weight change was detected at 1200°C. The weight loss was even greater in a reducing atmosphere ( P _O2= 5 × 10⁻⁵). Below 1300°C, the diffusion of elemental zinc was sufficiently fast to compensate the zinc loss at the interface region, resulting in a linear dependence on time. At temperatures ≥1400°C, the weight change no longer followed the linear dependence and showed a rather parabolic behavior with a concave upward slope. The core shape and the gas flow around ferrite cores were important factors that affected the rate of zinc vaporization, but not the grain size.     

液体消毒洗涤剂的研制

研制了具有消毒杀菌、洗涤去污双重功效的液体消毒洗涤剂 ,测定了其对金黄色葡萄球菌的杀灭效果。结果表明 ,消毒洗涤剂的杀菌效果随其浓度的增加 ,作用时间的延长而提高 ;戊二醛浓度为 2 0 0× 10 -6时 ,与金黄色葡萄球菌作用 5min ,杀灭率可达 99.99%。将消毒洗涤剂在室温下放置半年 ,戊二醛分解率为 17.3 1%     

聚苯胺/涤纶导电织物再掺杂及洗涤性能的研究

采用现场吸附聚合法制备了聚苯胺 /涤纶导电织物 ,采用不同种类的酸对其进行再掺杂 ,研究了酸的种类对织物导电性能的影响 ,并对导电织物进行了洗涤实验及洗涤牢度实验。结果表明 :无机酸对导电织物的掺杂效果优于大多数有机酸。导电涤纶织物的导电性能受洗涤液酸碱度的影响 ,其中碱性洗涤液使导电性能降低 2个数量级 ,酸性洗涤液使导电性能下降 1个数量级 ,而且聚苯胺在涤纶织物表面具有良好的附着性     

Solid circulation characteristics in an internally circulating fluidized bed with orifice-type draft tube

Effects of superficial gas velocities to a draft tube, to an annulus section and particle size on the solid circulation rate (G,) have been determined in an internally circulating fluidized bed (0.28 m I.D. × 2m high) with an orifice type draft tube. The solid circulation rate from the draft tube to an annulus section increases with increasing gas velocities to the draft tube(U _d ) and annulus section (U_a) and consequent increase in pressure drop across the orifice (ΔP_or). However, the values ofG _s decrease by 7–21% with increasing particle size from 86 to 288 μm. The pressure drop across the orifice increases with increasingU _d andU _a . However, ΔP_or decreases by 5–23% with increasing particle size. To predictG _s in an internally circulating fluidized bed, a correlation is proposed as a function of ΔP_or This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement Korea University.     

Axial dispersion of gas in a circulating fluidized bed

An axial dispersion of gas in a circulating fluidized bed was investigated in a fluidized bed of 4.0 cm I.D. and 279 cm in height. The axial dispersion coefficient of gas was determined by the stimulus-response method of trace gas of CO₂. The employed particles were 0.069 mm and 0.147 mm silica-sand. The results showed that axial dispersion coefficients were increased with gas velocity and solid circulation rates as well as suspension density. The experimentally determined axial dispersion coefficients in this study were in the range of 1.0-3.5 m²/s.     

Dynamics of liquid-liquid mixing: A 2-zone model

The development of multiphase liquid-liquid morphologies during mixing at small Reynolds numbers has been modeled. The mixing process is divided into (i) stretching of dispersed drops. (ii) breakup of the liquid threads formed, and (iii) coalescence of the final droplets upon collision. Rules and criteria of the distinct processes are presented and combined to a general 2-zone mixing model simplifying the flow field into a sequence of alternating “strong and weak zones.” In a “strong zone,” dispersed drops and threads are stretched unless their radius is too small; meanwhile, the stretching threads might break up into droplets. In the subsequent “weak zone,” the remaining threads may disintegrate while any drops present may coalesce. After passing a number of zones, stretching, breakup, and coalescence lead to a dynamic equilibrium that could be considered as the “final” morphology. Using the 2-zone mixing model, the influence of material parameters and processing conditions on the morphology has been studied. Interestingly, increasing either viscosity (dispersed or continuous phase) yields a finer morphology due to the delay of thread breakup, allowing for further stretching and suppression of coalescence.     

Ligand-binding domain of farnesoid X receptor (FXR) had the highest sensitivity and activity among FXR variants in a fluorescence-based assay

The farnesoid X receptor (FXR, NR1H4) has been recognized as an attractive therapeutic target because it is a nuclear hormone receptor that controls the expression level of cholesterol-7α-hydroxylase, which in turn regulates bile acid production and cholesterol excretion. To compare receptor activity between each domain and the full-length protein, human FXR cDNA was cloned from a human liver cDNA library. Three human FXR cDNA, designated FXR₂₀, FXR₃₃, and FXR₅₃ cDNA, were subcloned and ligated into a pET28a expression vector. Each protein was expressed in Escherichia coli (BL21) and purified by nickel-nitrilotriacetic acid column chromatography. Approximately 5 mg of FXR₃₃ (1–182 amino acids deleted from FXR, 37 kDa) and 2 mg of FXR₅₃ (the full-length protein of FXR, 59 kDa) was purified from 1 L of Luria-Bertani culture, achieving at least 90% purity. The coactivator recruitment assay for FXR activation was carried out with the three variants of the FXR protein by using dissociation-enhanced lanthanide fluoroimmunoassay-europium-N¹-labeled anti-His antibody. From an optimized assay, a saturated hyperbolic fluorescence signal curve was produced when 250 nM of FXR₃₃ and 100 nM of steroid receptor coactivator-1 peptide, a coactivator of FXR consisting of 26 amino acids, were used with a concentration dependence on chenodeoxycholic acid (from 0 to 200 μM). The ligand-binding domain of FXR (FXR₃₃) was the most suitable protein for studying the activation of FXR with a fluorescence-based assay, because it showed better structural stability than either the full length of FXR (FXR₅₃) or the DNA-binding domain of FXR (FXR₂₀).     

Low‐temperature photoinitiation solution polymerization behavior of N‐vinylcarbazole in tetrahydrofuran

N‐Vinylcarbazole (VCZ) was solution‐polymerized in tetrahydrofuran (THF) at ?20, 0, and 20°C using the photoinitiation method; the effects of the amount of solvent, polymerization temperature, and photoinitiator concentration were investigated. On the whole, the experimental results corresponded to predicted ones. Low polymerization temperature using photoinitiation proved to be successful in obtaining poly(N‐vinylcarbazole) (PVCZ) of a high molecular weight with a smaller temperature rise during polymerization; nevertheless of free radical polymerization by 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN). The photo‐solution polymerization rate of VCZ in THF was proportional to the 0.47 power of ADMVN concentration. The molecular weight was higher and the molecular weight distribution was narrower with PVCZ polymerized at lower temperatures. For PVCZ prepared in THF at ?20°C using a photoinitiator concentration of 0.00005 mol/mol of VCZ, a weight‐average molecular weight of 510,000 was obtained, with a polydispersity index of 1.73, and a degree of lightness converged to about 99%. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3667–3672, 2002     

砂带用酚醛树脂粘合剂的合成研究

本文讨论了砂带用酚醛树脂粘合剂的合成工艺和条件。研究了反应投料比，温度及增塑剂对反应过程和树脂性能的影响。磨削性能证明合成树脂性能良好。