Reduction of optical beat interference using gain-saturated RSOA in upstream WDM/SCM optical links

A new scheme for reducing optical beat interference (OBI) noise in optical network units is proposed for subcarrier multiplexing-based access network applications. The optical spectrum of the transmit lasers is broadened by using a radio frequency (RF) clipping tone with a modulation depth greater than one. This reduces the impact of the OBI noise. The distortions caused by an RF clipping tone are also suppressed by introducing a gain-saturated reflective optical amplifier, which shows the characteristics of high-pass filter. The proposed scheme has been verified by measuring the error vector magnitude of 16QAM signal with 20 Mbps. Error-free transmission has been achieved even when the light of OBI-noise-causing lasers is stronger than that of the signal laser by 7 dB     

Applying CIM technology to image factories

Image processing allows the automation of the business transaction, turning “paper factories” into “image factories.” This burgeoning new area of computerization needs new paradigms, theories, and methods to maximize its effectiveness at cutting time and costs. This paper investigates what this new area of computerization can gain from CIM technology. It examines the similarities between the processing of computer images in a paperless business environment and the processing of materials into products in the manufacturing plant. These similarities will allow us to apply mature, well-tested CIM techniques to emerging image factories.     

A 0.25-/spl mu/m CMOS quad-band GSM RF transceiver using an efficient LO frequency plan

This paper describes a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS applications. It is the most important design issue to maximize resource sharing and reuse in designing the multiband transceivers. In particular, reducing the number of voltage-controlled oscillators (VCOs) required for local oscillator (LO) frequency generation is very important because the VCO and phase-locked loop (PLL) circuits occupy a relatively large area. We propose a quad-band GSM transceiver architecture that employs a direct conversion receiver and an offset PLL transmitter, which requires only one VCO/PLL to generate LO signals by using an efficient LO frequency plan. In the receive path, four separate LNAs are used for each band, and two down-conversion mixers are used, one for the low bands (850/900 MHz) and the other for the high bands (1800/1900 MHz). A receiver baseband circuit is shared for all four bands because all of their channel spaces are the same. In the transmit path, most of the building blocks of the offset PLL, including a TX VCO and IF filters, are integrated. The quad-band GSM transceiver that was implemented in 0.25-/spl mu/m CMOS technology has a size of 3.3/spl times/3.2 mm/sup 2/, including its pad area. From the experimental results, we found that the receiver provides a maximum noise figure of 2.9 dB and a minimum IIP3 of -13.2dBm for the EGSM 900 band. The transmitter shows an rms phase error of 1.4/spl deg/ and meets the GSM spectral mask specification. The prototype chip consumes 56 and 58 mA at 2.8 V in the RX and TX modes, respectively.     

Cu—Zn—Al系合金热弹性马氏体相变的热滞

本文通过热处理工艺及添加第四组元研究了Cu－Zn－Al系记忆合金的相变热滞。结果表明，淬火冷却速度影响合金的相变热滞大小，随着母相时效时间的延长，马氏体相变热滞变大．Mn元素的加入可以减小CU－Zn－Al合金相变热滞．     

Fast DCT algorithm with fewer multiplication stages

A novel fast DCT scheme with reduced multiplication stages and fewer additions and multiplications is proposed. The proposed algorithm is structured so that most multiplications tend to be performed at the final stage, which reduces the propagation error that could occur in the fixed-point computation. Minimisation of the multiplication stages can further decrease the error     

Virtual circuit connection method for RSVP multicasting supportingheterogeneous receivers on the ATM network

The authors suggest a novel virtual circuit connection method based on the reverse traversing technique to minimise the waste of network bandwidth resources, when the Internet protocol multicast is interoperated using the resource reservation protocol over an asynchronous transfer mode network. Simulation results show that, as the number of receivers increases, the bandwidth requirements on all links of the network of the proposed scheme become more advantageous than those of other conventional methods     

An ARQ scheme using combined QPSK and BPSK transmissions

We propose a hybrid ARQ scheme which uses QPSK modulation for the first transmission and BPSK modulation for retransmissions. The throughput performance of the proposed ARQ scheme is better that those of ARQ schemes purely using QPSK modulation or purely using BPSK modulation for transmissions. Furthermore, the proposed scheme does not require any operation of error correction as usually required in hybrid ARQ schemes. Therefore, the ARQ scheme proposed in this paper can be easily implemented     

Directly Compressible Acetaminophen Compositions Prepared by Fluidized-Bed Granulation

Polyvinylpyrrolidone (PVP) in aqueous solution was used as a binding agent in a fluidized-bed system to agglomerate acetaminophen powder into directly compressible granules. It was found that a minimal amount of 5% w/w PVP in a concentration of 7.5% w/v or less was needed to produce granules with an acceptable flow and the corresponding tablets having enough hardness without capping. There was a strong correlation between the time for 80% dissolved (T₈₀) and the logarithm of granule volume-surface mean diameter. A directly compressible acetaminophen composition to manufacture tablets having a T₈₀ value less than 30 min can be prepared simply by adding an appropriate amount of disintegrant (crospovidone, sodium starch glycolate, or pregelatinized starch) to the agglomerated granules.