Structural characterisation of apatite coatings

The current, most frequently employed, commercial route to produce hydroxyapatite prosthetic coatings is plasma spraying. However, this has several important limitations especially for textured surfaces. Low temperature methods of coating fabrication such as cathodic electrodeposition are attractive alternatives. However, quantitative characterisation of the phase composition of thin electrodeposited coatings can be problematic. An X-ray diffraction method, which provides quantitative compositional information without reference to external or internal standards, is introduced and validated. The method can also be applied when Bragg peaks from the supporting substrate are apparent within the data and preferred orientation can be tolerated. This method has been used to examine in detail the microstructure of electrodeposited coatings which are compared directly with those formed by a commercial plasma spraying process.We show that, unlike the plasma sprayed coatings, the electrodeposited material consists of a single crystalline phase (hydroxyapatite) and a significantly reduced amorphous phase. The electrodeposited coatings also possess significantly more microstrain and a smaller crystallite size than the corresponding plasma sprayed material.     

A demonstration of melt rate control during VAR of “Cracked” electrodes

A particularly challenging problem associated with vacuum arc remelting occurs when trying to maintain accurate control of electrode melt rate as the melt zone passes through a transverse crack in the electrode. As the melt zone approaches the crack, poor heat conduction across the crack drives the local temperature in the electrode tip above its steady-state value, causing the controller to cut back on melting current in response to an increase in melting efficiency. The difficulty arises when the melt zone passes through the crack and encounters the relatively cold metal on the other side, giving rise to an abrupt drop in melt rate. This extremely dynamic melting situation is very difficult to handle using standard load-cell based melt rate control, resulting in large melt rate excursions. We have designed and tested a new generation melt rate controller that is capable of controlling melt rate through crack events. The controller is designed around an accurate dynamic melting model that uses four process variables: electrode tip thermal boundary layer, electrode gap, electrode mass and melting efficiency. Tests, jointly sponsored by the Specialty Metals Processing Consortium and Sandia National Laboratories, were performed at Carpenter Technology Corporation wherein two 0.43 m diameter Pyromet® 718 electrodes were melted into 0.51 m diameter ingots. Each electrode was cut approximately halfway through its diameter with an abrasive saw to simulate an electrode crack. Relatively accurate melt rate control through the cuts was demonstrated despite the observation of severe arc disturbances and loss of electrode gap control. Subsequent to remelting, one ingot was sectioned in the “as cast” condition, whereas the other was forged to 0.20 m diameter billet. Macrostructural characterization showed solidification white spots in regions affected by the cut in the electrode.     

HRTEM observation of the monoclinic-to-tetragonal m-t) phase transition in nanocrystalline ZrO2

The orientation relations m(100) || t(001), m[001] || t[110]; m(011) || t(100), m[100] || t[001]; m(100) || t(110), m[001] || t[001]; m(013) || t(116), m[001] || t[001] (indices for the primitive tetragonal cell) have been found between the tetragonal (t) and monoclinic (m) domains during the electron irradiation-induced m-t phase transition observed in-situ with HREM within isolated zirconia nanoparticles. Geometric models of the m-t interfaces are proposed.     

Magnetic properties and thermal stability of CoFeNi-based amorphous films

CoNiFe-based amorphous films were magnetron-sputtered to investigate their structural and magnetic properties, including annealing-induced effects and interfacial influence from additional layers of Ta and Cu. The amorphous structure was confirmed by diffraction experiments. The magnetic measurements showed a well-defined uniaxial anisotropy in plane, arising possibly from atom oblique incidence effects competing with the stray field of the magnetron. The anisotropy could be influenced by using a Ta buffer layer, though the interfacial reaction gives rise to a dead layer. A coercive force H _c of 1–2 Oe and a magnetization of 680 emu/cm³ were measured at room temperature; properties which show promise for application in magnetotunneling junction devices. Thermal analyses showed a two-stage crystallization behavior, which started at 400°C and ended at about 600°C. The Curie temperature of the amorphous phase was estimated to be about 440°C.     

Modelling induction skull melting design modifications

Induction Skull Melting (ISM) is used for heating, melting, mixing and, possibly, evaporating reactive liquid metals at high temperatures when a minimum contact at solid walls is required. The numerical model presented here involves the complete time dependent process analysis based on the coupled electromagnetic, temperature and turbulent velocity fields during the melting and liquid shape changes. The simulation is validated against measurements of liquid metal height, temperature and heat losses in a commercial size ISM furnace. The often observed limiting temperature plateau for ever increasing electrical power input is explained by the turbulent convective heat losses. Various methods to increase the superheat within the liquid melt, the process energy efficiency and stability are proposed.     

Electrophoretic deposition of monochrome and color phosphor screens for information displays

This paper reviews our research on the electrophoretic deposition (EPD) of phosphors for the processing of monochromatic and color screens for information displays. Our investigation began with the study of the fundamentals of the EPD process for phosphors. The processing variables which enhance the adhesion strength of phosphor deposits were determined. The optical performance of phosphors deposited by EPD was shown to be not affected by the process itself nor by the conditions which enhance phosphor adhesion. Processes developed to produce high-resolution color screens by combining EPD and photolithography techniques are described. Also, a method to electrophoretically deposit phosphor in a thermo-reversible gel from mixtures of poly(butyl methacrylate) and isopropanol was examined.