Recrystallization and precipitation behavior of low-activation V-Cr-Ti alloys after cold rolling

Recrystallization and precipitation behavior after cold working were investigated for three V-4Cr-4Ti alloys, NIFS-HEAT-1, NIFS-HEAT-2 and US 832665, which contain different levels of impurities. The decrease in hardness and the initiation of recrystallization against test temperature do not depend on the oxygen level. However, the rate of grain growth decreased with the increase in the impurity levels. Bimodal distribution of the precipitates was observed after annealing at 1273 K. The large precipitates were Ti-rich precipitates, and the small ones were composed mainly of Ti, C and O (Ti-C-O precipitates). The impurities were dissolved from Ti-C-O precipitates above 1273 K, and the level of impurities in the matrix increased and resulted in the increase in the hardness. Based on the results, the annealing temperature for V-4Cr-4Ti alloys is recommended not to exceed 1273 K for the purpose of maintaining good mechanical properties such as tensile and impact properties.     

Development of Nanoscale Temperature Measurement Technique Using Near-field Fluorescence

A nanoscale thermal system design, especially for the precise measurement of the temperature distribution in microfabricated devices using novel nanomaterials such as carbon nanotubes and fullerene has become increasingly important along with the development of nanotechnology. A new approach has been proposed toward an optical nanoscale temperature measurement method using near-field optics and fluorescence thermometry, namely, Fluor-NOTN (fluorescent near-field optics thermal nanoscopy). The topographic image and temperature dependence of a fluorescently modified sample, excited by near-field light, are simultaneously monitored. In this article, the temperature dependence of Cy3 fluorescent dye is verified near room temperature (298–308 K). A Cy3 mono-dispersed sample of a permalloy (Ni₈₁Fe₁₉) wire heater, 500 nm in width and 100 nm in thickness, is designed and fabricated. A localized temperature gradient of ΔT = 4 K within a submicron distance from the heater was successfully detected by near-field fluorescence with 100 nm spatial resolution.     

Pre-emptive analgesia from intravenous administration of opioid: no effect with pentazocine

The influence of timing of administration of preoperative pentazocine on pain and analgesic requirements after surgery was studied in 46 patients undergoing total abdominal hysterectomy. Twenty-three patients received thiamylal 5 mg.kg-1 on induction of anesthesia, followed by pentazocine 30 mg or 60 mg before surgical incision (group A). Twenty-three control patients received pentazocine 30 mg or 60 mg, 5 min after abdominal incision (group B). The visual analogue scales for pain 24 h after operation were 6.0 cm at 30 mg dose in group A or 5.3 cm at 60 mg dose in group A and 5.7 cm at 30 mg dose in group B or 4.7 cm at 60 mg dose in group B. There were no differences in the visual analogues scales. Pentazocine consumption in the first 24 h after surgery was 67.5 mg at 30 mg dose in group A or 52.5 mg at 60 mg dose in group A and 70.9 mg at 30 mg dose in group B or 51.8 mg at 60 mg dose in group B. We conclude that postoperative pentazocine consumption and pain scores are no different when pentazocine is given before or after skin incision for abdominal hysterectomy and that there is no clinically useful pre-emptive analgesic effect with these doses of pentazocine.     

The deformation of beams structured by thin walls

Nowadays our society demands the reuse of industrial products. Then we should not only re-investigate the materials of products but also originate a new design method of industrial products. We have investigated the cellular structure by using abandoned paper, because the cell's shape can be proposed arbitrarily by folding a paper. As examples, we have proposed the structure constructed by connecting many folded cells formed in a hexagonal cross area. This structure will have characteristics such as almost high rigidity, high stiffness, crushing stress, relative insensitivity to the overall loss of stability. To estimate the characteristics of these structures, we must analyze the deformation in loading. When the structure with thin walls formed by paper is loaded, the shape of deformation is different from that of the metal, wall swells and does not maintain its flatness. Therefore, we cannot apply the traditional theory of elasticity for the analysis. In this paper, we propose a new estimation method by analyzing the swelling.     

Time‐frequency analysis of a pressure wave caused by impulse tree using wavelet transform

This paper describes results of time‐frequency analysis of a pressure wave caused by impulse tree extension using wavelet transform. Pressure waves were measured by a piezo sensor which was located on the back of the plane electrode when high‐voltage nanosecond pulses were applied to a point electrode in a low‐density polyethylene block. Frequency of the pressure wave from induced charges on the plane electrode was higher than that of the pressure wave from tree. In addition, the frequency of the pressure wave from tree tended to decrease with increasing gap length because of the dispersion of the pressure wave during its propagation. When a large tree extension occurred between a 5‐mm gap, pressure waves of about 10 MHz propagated from the tree tip and a pressure wave of 1 MHz propagated from the tree stem. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 142(1): 1–7, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10097     

Gas absorption into “string-of-beads” liquid flow with chemical reaction: application to carbon dioxide separation

This study examines the performance of “string-of-beads” liquid flow on vertical wires as a novel gas-liquid contact device for gas absorption using a chemically reacting liquid absorbent. The string-of-beads flow is a distinct on-wire liquid-flow pattern consisting of annular thin liquid films sheathing a wire and teardrop-shaped liquid beads alternately aligned on the wire at regular intervals. We have performed experiments of CO₂ absorption by an aqueous monoethanolamine solution in string-of-beads flow on a single wire and have developed an analytic gas-absorption model relevant to the experiments. The model well simulates the CO₂-absorption characteristics observed in the experiments, thereby suggesting the utility of the model in predicting the chemical gas-absorption performance of multiple-wire gas-liquid contactors.     

Tool wear prediction and economics in machining stepped parts

For analysing economics of machining cylindrical stepped parts, tool life must be predicted. In this paper, tool life tests, to obtain tool life changing cutting speed before the tool reaches tool life criterion under a constant speed, are performed and the tool life is calculated. Using the results of the calculations machining economics of various forms of stepped parts for the constant spindle rpm method and the constant cutting speed method, are analysed.     

Vitamin E and coenzyme Q concentrations in the thyroid tissues of patients with various thyroid disorders

Chylous fistula complicates 1.1% of all radical neck dissections, and 2.4% of left-sided dissections. The standard treatment of established chylous leak in the reported cases is a pressure dressing applied to the lower neck. Here we present a case of chylous fistula, where conservative methods failed to cope with this complication. The additional application of a fibrin adhesive set was a successful modality of treatment.