Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

STRUCTURE FORMATION OF COATED FILMS WITH DISPERSED PIGMENTS DURING DRYING

In the drying of coated films with dispersed pigments, such as floppy disks, the structure of the film is formed during the drying process and depends on the drying condition. It is important to understand the structure formation during drying for the design of the dryer and die better quality of the product. We measured die drying characteristics of the film and determined the structure of dried film experimentally. A qualitative model for the structure formation during drying of the coated film is suggested.     

Feedback regulation of hand grasp opening and contact force duringstimulation of paralyzed muscle

A fixed-parameter, discrete-time, first-order, feedback control system is described for regulating grasp during electrical stimulation of paralyzed muscles of the hand. The stiffness of the grasp (relationship between grasp force and grasp opening) is kept constant by linearly combining force and position feedback signals. Thus, a single continuous command signal can control the size of the grasp opening prior to object acquisition and both grasp force and opening after contact. The controller achieves this change in controlled variables by scaling and summing the force and position feedback signals, rather than by a discrete switch in control strategy. Experimental tests of the control system in quadriplegic subjects show that control can be obtained over conditions ranging from unloaded position regulation to isometric force regulation, as well as in the transition between these conditions. The robustness of the control system was evaluated during force regulation with isometric loads. Step response rise time and overshoot were much more dependent on system gain than on the location of the controller zero. Responses with rise time less than two seconds and overshoot less than 30% were obtained over a gain range up to ten, indicating good robustness to muscle gain reductions such as might be caused by fatigue.     

Heat Generation in Multilayer Piezoelectric Actuators

Multilayer piezoelectric actuators when driven under high frequency, generate significant heat, which influences the reliability and other piezoelectric properties. In this paper, heat generation in various types of multilayer PZT-based actuators was studied. Experimental results showed that heat generation is mainly caused by ferroelectric hysteresis loss in the stress-free state. A simplified analytic method was established to evaluate the temperature rise, which is useful for the design of multilayer and other high-power actuators.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Band Gaps of Na2C60 and K4C60

respectively.     

Bottom-up multi-agent reinforcement learning by reward shaping for cooperative-competitive tasks

Applied Intelligence - A multi-agent system (MAS) is expected to be applied to various real-world problems where a single agent cannot accomplish given tasks. Due to the inherent complexity in the...