Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Purification of Ellagic Acid by UF Membranes

Ellagic acid (2, 3, 7, 8‐tetrahydroxy(1)benzopyrano(5, 4, 3‐cde)(1)benzopyran‐5, 10‐dione) was selected as a model pollutant which is present in the tannic fraction of cork processing wastewater. The ultrafiltration of aqueous ellagic acid solutions through three membranes was studied in tangential UF laboratory equipment. Two of the membranes were polyethersulfone (Biomax10K and Biomax5K, with MWCO of 10000 and 5000 Da, respectively), and the third made of regenerated cellulose (Ultracel5K, with MWCO of 5000 Da). The water hydraulic permeability was evaluated for each membrane. The evolution of the permeate flow rate with processing time was followed, and the influence of the main operating variables (feed flow rate, trans‐membrane pressure and nature of the membranes) on the permeate flux was also established. According to the hypothesis of the film theory, the intrinsic and apparent rejection coefficients, as well as the mass transfer coefficients, were also determined, and the values obtained were discussed as a function of the operating conditions used.     

A case study of regional catchment water quality modelling to identify pollution control requirements.

There are four ecologically important river catchments that contain candidate Special Areas of Conservation (cSACs) under the Habitats Directive in the Lake District National Park located in the North of England. These are the rivers Ehen, Kent, Derwent and Eden. For each cSAC, there are defined ecological criteria that include water quality targets to protect the designated species. Stretches of the riverine cSACs in each catchment are failing to meet these and other water quality targets. The Environment Agency commissioned a study of each catchment to provide the underpinning scientific knowledge to allow it to deliver its statutory obligations under the Habitats Directive. SIMCAT river water quality models were produced and used to predict the water quality impacts resulting from a number of water quality planning scenarios aimed at achieving full compliance with the Habitats Directive and other national and EEC water quality targets. The results indicated that further controls on effluent discharges will allow the majority of targets to be met but other sources of pollution will also need to be controlled. The outcome of the study also recognised that water quality improvements alone will not necessarily produce the required improvement to the ecological interest features in each cSAC.     

Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.     

MALL在中国的现状及其建筑设计要点

该文介绍了Mall的产生条件和国内发展概况，并结合实例分析，着重论述建筑设计方面的有关问题。     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry