长庆油田气井固井技术

长庆油田陕北安塞地区气井埋深一般为3500～4000m，底部气层活跃，上部地层撑压能力差，钻井和固井易发生满失。针对该地区的地质情况、钻井情况、固井情况，制定出了一整套气井固井工艺方案，并根据工艺要求，经过室内大量的模拟试验，研究出了6组水泥浆体系。在固井过程中采用分级注水泥工艺和3种密度、3种稠化时间的防窜、防满水泥浆体系。3口井的固井实践证明，该套固井工艺切实可行，固井水泥浆体系有利于气井固井施工，保证了固井质量．气层井段固井质量优质。     

推进波作用下的底泥起动

在介绍推进波作用下底泥起动特点的基础上，将上层水体作为粘性流体，底泥作为粘弹性体，推导了推进波作用下泥床面剪应力的表达式，并根据试验结果，给出了推进波作用下底泥起动时的床面剪应力与底泥流变参数的关系。     

钢铁表面黑色转化膜处理技术

黑色转化膜技术是目前较为先进的钢铁表面处理技术 ,本文试验研究了一种新工艺 ,提出了TB值的概念 ,通过控制TB值即可控制处理液的质量 ,获得性能优良的转化膜。此工艺性能可靠 ,可操作性强 ,并可应用于激光热处理前的预处理。     

Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.     

一种控制盐层段井眼闭合率的钻井液密度新公式

针对钻井过程中钻遇的盐层段井眼蠕变缩径问题,利用弹塑性力学理论,蠕变本构方程采用Heard蠕变方程,在平面应变和均匀地应力假设下,推导出控制井眼收缩的钻井液密度新公式,该公式与前人推导的公式不同。通过理论分析,指出产生差异的根本原因在于蠕变应力差(极坐标下表示的径向应力与切向应力之差)公式的推导上,用有限元法计算结果对理论公式进行检验,证明是可行的。对文中的力学模型采用有限元法建模、求解,利用求解结果对各应力差公式进行验证,得出:根据文中公式计算结果与有限元法计算结果完全一致,而据前人公式计算结果偏离有限元计算值较大,从而间接证明了该钻井液密度新公式的推导更严密,更准确。     

汽轮机转子热应力在线计算灰色数学模型

热应力计算中边界条件、物性参数和初始条件等模型输入参数的灰色特性，使得以近似点值为输入得到的计算结果缺乏准确性依据和度量，该文提出的灰色数学模型，用区间数代替近似点值建立灰色数学模型，得出热应力在线计算值的灰色描述，可以更好地符合工程计算需要。文中针对模型应用的复杂程度，以汽轮机转子为对象，对单纯灰边界问题给出了简单的端点计算法及其依据；对复合灰边界灰物性问题建立了差分格式的数学模型，应用区间高斯迭代算法，结合模型结构特点推导了简易的基于内包含不等式的算法，并且给出两种算法的数值算例对比。     

用于数控设备的弹性环联轴器

介绍了一种适用于数控设备改造的无键联轴器，从其原理、设计、加工各方面作了阐述，并且总结了许 多实际应用经验和适用参数。     

Joint spatial registration and multi-target tracking using an extended PM-CPHD filter

An extended product multi-sensor cardinalized probability hypothesis density (PM-CPHD) filter for spatial registration and multi-target tracking (MTT) is proposed. The number and states of targets and the biases of sensors are jointly estimated by this method without the data association. Monte Carlo (MC) simulation results show that the proposed method (i) outperforms, although computationally more expensive than, the extended multi-sensor PHD filter which has been proposed for joint spatial registration and MTT; (ii) outperforms the multi-sensor joint probabilistic data association (MSJPDA) filter which is also extended in this study for joint spatial registration and MTT when the clutter is relatively dense.