Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Crystallographic characteristics and microwave dielectric properties of Ni-modified MgTa2O6 ceramics

Ni²⁺ modified MgTa₂O₆ ceramics with a trirutile phase and space group P4₂/mnm were obtained. The correlations between crystallographic characteristics and microwave dielectric performance of MgTa₂O₆ ceramics were systematically studied based on the chemistry bond theory (PVL theory) for the first time. The results indicate that the introduction of Ni²⁺ causes a change in polarizability and the Mg–O bond ionicity, which contributes to the variation of dielectric constant. Moreover, the lattice energy, and packing fraction, full width at half maximum of the Raman peak of Ta–O bond, as the quantitative characterization of crystallographic parameters, regulate the dielectric loss of MgTa₂O₆ ceramics in GHz frequency band. In addition, the study of sintering behavior shows that the densification and micromorphology are the crucial factors affecting the microwave dielectric performance. Typically, Ni²⁺ doping on the A-site of MgTa₂O₆ can effectively promote the Q × f values to 173,000 GHz (at 7.43 GHz), which ensures its applicability in 5G communication technology.     

Investigation of crystal characteristics,Raman spectra,and microwave dielectric properties of Mg1-xZnxTa2O6 ceramics

Mg_(1-x)Zn_xTa₂O₆ (x = 0.00?0.08) dielectric ceramics were synthesized via the traditional solid-state reaction method. We used XRD and Rietveld refinement to demonstrate that a pure Mg_(1-x)Zn_xTa₂O₆ phase with trirutile structure was formed. Zn²⁺ substitution helped to decrease the Raman full width at half width of the A_1g mode at 703 cm^?1, which resulted in an increase in the order and rigidity of the TaO₆ octahedron, this in turn contributed to improving the Q×f values. Additionally, the introduction of Zn²⁺ significantly promoted grain growth and increased the dense, and the molecular polarizability, these factors lead to a higher permittivity. Moreover, enhanced Ta-O bond energy resulted in a more stable TaO₆ octahedron in the Mg_(1?x)Zn_xTa₂O₆ system, which contributed to enhanced τ_f values via substitution of Zn²⁺ doped on the A-site. Correspondingly, the microwave dielectric properties were significantly improved for 0.04-doped samples, obtaining: ε_r = 27, Q × f = 185,000 GHz (at 7.47 GHz), τ_f =32 ppm/°C.     

基于模糊谱聚类的不确定蛋白质相互作用网络功能模块挖掘

针对谱聚类融合模糊C-means（FCM）聚类的蛋白质相互作用（PPI）网络功能模块挖掘方法准确率不高、执行效率较低和易受假阳性影响的问题，提出一种基于模糊谱聚类的不确定PPI网络功能模块挖掘（FSC-FM）方法。首先，构建一个不确定PPI网络模型，使用边聚集系数给每一条蛋白质交互作用赋予一个存在概率测度，克服假阳性对实验结果的影响；第二，利用基于边聚集系数流行距离（FEC）策略改进谱聚类中的相似度计算，解决谱聚类算法对尺度参数敏感的问题，进而利用谱聚类算法对不确定PPI网络数据进行预处理，降低数据的维数，提高聚类的准确率；第三，设计基于密度的概率中心选取策略（DPCS）解决模糊C-means算法对初始聚类中心和聚类数目敏感的问题，并对预处理后的PPI数据进行FCM聚类，提高聚类的执行效率以及灵敏度；最后，采用改进的边期望稠密度（EED）对挖掘出的蛋白质功能模块进行过滤。在酵母菌DIP数据集上运行各个算法可知，FSC-FM与基于不确定图模型的检测蛋白质复合物（DCU）算法相比，F-measure值提高了27.92%，执行效率提高了27.92%；与在动态蛋白质相互作用网络中识别复合物的方法（CDUN）、演化算法（EA）、医学基因或蛋白质预测算法（MGPPA）相比也有更高的F-measure值和执行效率。实验结果表明，在不确定PPI网络中，FSC-FM适合用于功能模块的挖掘。     

Study of haze emission efficiency based on new co-opetition data envelopment analysis

As haze intensifies in China, controlling haze emission has become the country's top priority for environmental protection. Because haze moves across different regions, it is necessary to develop a data envelopment analysis (DEA) model underpinned by both competition and cooperation to evaluate the haze emission efficiency in different provinces. This study innovatively adopts the spatial econometrics to construct the co-opetition matrices of Chinese provinces, then builds the co-opetition DEA model to evaluate the haze emission efficiency of them, and finally uses the haze data of 2015 as an example to assess the applicability of the model. The results of the study include the following: First, compared with the traditional CCR (A. Charnes & W. W. Cooper & E. Rhodes) model, this study constructs the co-opetition DEA cross-efficiency model that integrates haze's feature of cross-border moving; thus, it is more in line with the reality of haze emission and movement. Second, compared with the efficiency value gained from the CCR model, the haze emission efficiency values for Tianjin and Guangdong, two decision-making units, register greater variance when using the DEA model. The reason might lie in that they have a different spatial transportation relationship with their surrounding provinces. Third, the haze emission efficiency of provinces, according to the evaluation based on the co-opetition DEA method, varies greatly: Those with high efficiency are mostly inland provinces with slow economic growth and adverse climatic conditions, whereas many of the provinces with low efficiency are located in the relatively prosperous East China. The specific co-opetition DEA model constructed in this study enriches the research on the DEA model, which can be applied to the emission efficiency evaluation of similar pollutants around the world and can contribute empirical support to the haze reducing efforts of the government with its empirical results.     

Data sharing mechanism of various mineral resources based on blockchain

Basins with various mineral resources coexisting and enriching often occupy an important strategic position. The exploration of various mineral resources is repetitive at present due to unshared data and imperfect management mechanism. This situation greatly increases the cost of energy exploitation in the country. Traditional data-sharing mode has several disadvantages, such as high cost, difficulty in confirming the right of data, and lack of incentive mechanism, which make achieving real data sharing difficult. In this paper, we propose a data-sharing mechanism based on blockchain and provide implementation suggestions and technical key points. Compared with traditional data-sharing methods, the proposed data-sharing mechanism can realize data sharing, ensure data quality, and protect intellectual property. Moreover, key points in the construction are stated in the case study section to verify the feasibility of the data-sharing system based on blockchain proposed in this paper.     

Preparation and electrochromism of pyrochlore-type tungsten oxide film

Pyrochlore-type WO_3 powder was synthesized via hydrothermal method using aqueous sodium tungstate solution and oxalic acid as raw materials. The as-prepared powder was made into a soliquoid,from which films were made by dip coating process with indium-tin oxide(ITO).The obtained films were characterized by thermogravimetric and differential thermal analysis(TG-DTA), X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM), cyclic voltammetry(CV), chronoamperometry(CA) and ultravioletvisible(UV-Vis) absorption. Results show that the crystal of the pyrochlore-type WO_3 powder is perfect. When the calcination temperature rises from room temperature to500 ℃,the pyrochlore-type structure first becomes deformed, then it is destroyed and turns into amorphous phase,finally it will completely convert to WO_3 with a monoclinic structure. Electrochemical and optical tests demonstrate that the film calcined at 300 ℃ exhibits the best electrochromic performance and has a coloration efficiency of up to 68.5 cm~2 C~(-1) at 884 nm.     

快速灵敏的LC-MS/MS法测定人血浆中阿莫西林并应用于两种制剂的一致性评价

目的: 建立快速灵敏的LC-MS/MS法测定人血浆中阿莫西林浓度，并用于两种阿莫西林胶囊的一致性评价。方法: 采用岛津公司LCMS-8060型LC-MS/MS仪，以MRM模式测定阿莫西林（m/z 366.00/114.00）的浓度，d4-阿莫西林作内标（m/z 370.10/114.05），离子源为ESI源。色谱柱选用Waters ACQUITY BEH C18（2.1×50 mm，1.7 μm），梯度洗脱。血浆样本加入内标，经甲醇沉淀蛋白后取上清液进样检测。结果: 所建方法经验证，其线性、准确度、精密度、最低定量限、提取回收率、特异性、基质效应、稳定性等各项指标均符合CFDA的指导原则及最新核查标准要求，并较文献报道中的方法有处理简单、灵敏度高、色谱峰形好的优点。结论: 所建方法快速、灵敏，适用于人血浆中阿莫西林浓度的检测。用于一致性评价的样本实测，两种制剂生物等效。     

Design and optimization of ceramic membrane structure: From the perspective of flux matching between support and membrane

The support flux was first investigated as a separate influencing factor for its effect on performances of ceramic filtration membranes. Three pre-membranes were prepared by tape-casting and then transfer-coated to supports to form dual-layer ceramic membranes after sintering. Experiments demonstrated that membrane layers with almost the same properties were obtained despite the huge difference in support flux. When the support flux increases from 3.120 to 97.53 m³m^?2h^?1, the flux of these three membrane series have increased by 75%, 186% and 228%, respectively. Experimental rules can provide structural design and evaluation from the perspective of permeability. The limit membrane flux of a certain system was derived according to the resistance distribution law of internal membrane structure and the Darcy's theorem. On this basis, a method for designing support flux was proposed. Furthermore, we present a criterion to quickly and easily evaluate the match between the support and the top layer, which is the ratio of membrane resistance to total resistance. Finally, the filtration resistance of penetration caused by suction of membrane particles into the support was measured for the first time, taking the advantage of the transfer-coating method that inherently free of penetration. Our works are expected to deepen the understanding of the ceramic membrane structure and provided guidance for its rational design and optimization.