多级脉冲深穿透射孔技术

目前国内较先进的射孔工艺是增效射孔和三相流射孔,这2种射孔工艺均存在射孔深度和造缝深度浅的问题,尤其是对低渗油藏和纵向渗透率远大于横向渗透率的油藏,此造缝深度并不能满足油田生产的需要.介绍了一种新型的射孔技术,它是一种能进行深度射孔造缝的多级射孔技术,利用三级推进剂燃爆时产生峰值不连续的高温、高压气流,形成多级脉冲,多次冲击射孔孔眼前沿的裂缝,使其有效延伸至地层深处,从而较单独的射孔更能有效地增加油气产量.通过地面水泥靶的试验,证明了该射孔器的延缝功能和安全性;通过塘32等井的现场试验,证明该射孔技术对污染地层解堵有显著效果,可明显地降低地层破裂压力.     

Fast acquisition clock and data recovery circuit with low jitter

This paper presents a half-rate clock and data recovery circuit (CDR)that combines the fast acquisition of a phase selection (PS) delay-locked loop (DLL) with the low jitter of a phase-locked loop (PLL). The PLL acquisition time improves considerably with use of a phase frequency magnitude detector(PFMD) that feeds back an estimate of the magnitude of the frequency difference in addition to the sign. Measurements in 0.5/spl mu/m CMOS technology show operation up to 700 Mb/s, a 7% acquisition range, an initial acquisition time of 8 bit times with jitter of 30% bit time, and jitter of 16 ps after the PLL acquires lock. With a phase frequency detector (PFD), the PLL locks in about 700 ns from an initial frequency difference of 7%. Measurements using a PFMD show the 700 ns PLL acquisition time is reduced on average by about a factor of 5 to 140 ns from an initial 7% frequency difference. The power dissipation is 300mW.     

木质装饰材料干缩湿胀性对家具拼口的影响

随着装饰业、家具制造业的强劲发展,对于木质材料干缩湿胀性研究尤为重要,企业渴望得到解决木质材料干缩湿胀性的技术。本文在分析了大量文献的基础上,简述了国内外木质材料干缩湿胀性的研究成果,并提出了一些对家具制造具有实用价值的措施。     

以质量管理体系为基础建立实施整合型QHSE管理体系

通过体系整合的必要性和可行性分析,介绍运用管理的系统方法,以质量管理体系为基础,策划、推进及实施整合型QHSE管理体系的做法,并对各阶段体系建立的方法与措施进行阐述。     

熔炼钼合金的挤压加工

分析了熔炼钼合金在挤压加工中的影响因素,指出在研制中设备、工艺等方面所存在的实际问题,指出目前国内可用于难熔金属加工的挤压设备老化严重,严重阻碍了熔炼钼合金的深入研究.     

河道维护费征收中需注意的几个问题

依法征收河道工程维护费,是水行政主管部门的一项重要职能,是强化水利依法管理的重要手段和筹措水利建设资金的重要途径。随着依法行政进程的不断推进,被征管单位依法维权的意识不断增强。根据《行政诉讼法》的规定,人民法院审查行政案件,对具体行政行为是否合法进行审查。根据《行政复议法》的规定,复议机关审查复议案件,对具体行政行为是否合法     

Lake-Level Change and Water Balance Analysis at Lake Qinghai,West China during Recent Decades

Lake Qinghai, the largest saline lake with an area of 4,260 km² (2000) and average depth of 21 m (1985) in West China, has experienced severe decline in water level in recent decades. This study aimed to investigate water balance of the lake and identify the causes for the decline in lake level. There was a 3.35-m decline in water level with an average decreasing rate of 8.0 cm year⁻¹ between 1959 and 2000. The lake water balance showed that mean annual precipitation between 1959 and 2000 over the lake was 357 ± 10 mm, evaporation was 924 ± 10 mm, surface runoff water inflow was 348 ± 21 mm, groundwater inflow was 138 mm ± 9 and the change in lake level was −80 ± 31 mm. The variation of lake level was highly positively correlated to surface runoff and precipitation and negatively to evaporation, the correlation coefficients were 0.89, 0.81 and −0.66, respectively. Water consumption by human activities accounts for 1% of the evaporation loss of the lake, implying that water consumption by human activities has little effect on lake level decline. Most dramatic decline in lake level occurred in the warm and dry years, and moderate decline in the cold and dry years, and relatively slight decline in the warm and wet years, therefore, the trend of cold/warm and dry climate in recent decades may be the main reasons for the decline in lake level.     

Numerical simulation of two-phase turbulent flow in hydraulic and hydropower engineering

In connection with the specific features of high velocity aerated flow generated by hydraulic engineering structures, the mathematical model is developed for high turbulence air-water two-phase flow with the use of twin flow theoretical model in this paper. Furthermore the numerical method is proposed to treat bubbled flows. In addition, on the basis of air-water stratified twin flow model, the new calculation methods and free surface tracking technique are proposed to describe complicated movements of the free surface. Finally, the proposed model is used to calculate artificial aerated flows. The computed results coincide quite well with experimental results. This means that the proposed method can provide solid basis for practical engineering design.