Pretreatment of polyamide monofilament with hydrochloric acid improves sensitivity of three-dimensional microarray, Bio-Strand

A single-nucleotide-polymorphism-typing method using a novel three-dimensional DNA microarray, Bio-Strand, is promising because it is rapid, inexpensive and easily automated. It has been developed with the intent to overcome the drawbacks of conventional DNA microarrays, which use flat surfaces and impermeable materials such as glass slides; Bio-Strand as a novel DNA microarray, with its permeability, has a significantly improved stability compared with conventional DNA microarrays that use impermeable materials. In this study, we have developed a simple method of pretreating a polyamide monofilament to increase its surface area and to make it permeable, which makes Bio-Strand more sensitive and stable, allowing it to be adapted for clinical diagnostic applications. The fluorescence signal obtained with a nylon 6 monofilament pretreated under optimal conditions (hydrolysis by 5 M HCl/ethanol followed by washing with 50% ethanol and 100% ethanol) was significantly stronger than that obtained with an untreated monofilament.     

Removal of p-xylene with Pseudomonas sp. NBM21 in biofilter

As a p-xylene (p-Xyl)-degrading microorganism, Pseudomonas sp. NBM21 was isolated from an activated sludge of a wastewater treatment plant. NBM21 degraded p-Xyl, m-xylene, benzene and toluene, but not o-xylene, ethylbenzene (Eb) and styrene. NBM21 was inoculated to a biofilter with Biosol as a packing material and p-Xyl removal was operated for 105 d under sterile and nonsterile conditions. The maximum elimination capacities for p-Xyl at higher than 90% removal efficiency were 160 g/m3/h and 150 g/m3/h under nonsterile and sterile conditions, respectively. A high load of Eb adversely affected to the removal of xylene.     

Fabrication of a polymer-coated silver hollow optical fiber with high performance

The techniques for fabricating a hollow optical fiber with an inner silver layer and a cyclic olefin polymer (COP) layer have been improved to reduce the surface roughness of these two layers. The loss spectrum was thereby drastically reduced over a wide wavelength range, from visible to near infrared. Optimization of the COP layer thickness resulted in low loss simultaneously at several key laser wavelengths. Infrared hollow fiber with low loss was developed for Er:YAG and Nd:YAG lasers. It can also deliver green and red pilot beams with low loss. Use of this fiber in therapeutic and pilot lasers should prove useful for research and development in laser medicine.     

In situ Raman study on single- and double-walled carbon nanotubes as a function of lithium insertion

We investigated the electrochemical lithium ion (Li(+)) insertion/desertion behavior on highly pure and bundled single- and double-walled carbon nanotubes (SWNTs and DWNTs) using an in situ Raman technique. In general, two storage sites could host Li(+) in SWNT and DWNT bundles when varying an external potential: a) the outer surface sites, and b) the interstitial spaces within the bundles. The most sensitive changes in the tangential mode (TM) of the Raman spectra upon doping with Li(+) can be divided into two regions. The first region was found from 2.8 to 1.0 V (the coverage of Li(+) on the outer surface of a bundled nanotube) and was characterized by the loss of resonant conditions via partial charge transfer, where the G(+) line of the SWNT and the TM of the outer tube of DWNTs experienced a highly depressed intensity, but remained almost constant in frequency. The appearance of a Breit-Wigner-Fano (BWF) profile provided strong evidence of metallic inner tubes within DWNTs. The second region was observed when the applied potentials ranged from 0.9 to 0 V and was characterized by Li(+) diffusion into the interstitial sites of the bundled nanotube material. This phenomenon invoked a large downshift of the G(-) band in SWNTs, and a small downshift of the TM of the inner tube of DWNTs caused by expansion of the C--C bonds due to the charge transferred to the nanotubes, and the disappearance of the BWF profile through the screening effect of the interstitial Li(+) layers.     

Surface-modified mesoporous silicas as recyclable adsorbents of an endocrine disrupter, bisphenol A

Surface-modified mesoporous silicas (MSs) were investigated for recyclable adsorption of an endocrine disrupter, bisphenol A (BPA). Surface-modified MSs were prepared by (i) post-synthesis surface modification of MSs using surface hydroxyl groups and organosilanes (m-MS) and by (ii) co-condensation of tetraethoxysilane and the corresponding organosilanes (d-MS). Infrared measurements indicated that organic groups mainly existed on the surface of m-MS, which resulted in a surface characterized by high hydrophobicity. Both organic groups and isolated hydroxyl groups existed on the surface of d-MS, resulting in both hydrophobicity and hydrophilicity on the surface. The amount of BPA adsorbed on surface-modified MSs per organic group was similar for m-MS and d-MS, however, the d-MS established equilibrium for BPA adsorption faster than m-MS, as measured by UV-vis spectra. A larger amount of BPA per surface area could be adsorbed on carbon materials than on the surface-modified MSs, however, the regeneration of carbon materials by washing could not be done easily. The surface-modified MSs retain adsorption capacity for BPA after several regeneration cycles, demonstrating that the surface-modified MSs are effective recyclable adsorbents of the endocrine disrupter, bisphenol A.     

Evidence for intergranular tunnelling in polyaniline passivated α-Fe nanoparticles

Nanoparticles are of immense importance both from the fundamental and application points of view. They exhibit quantum size effects which are manifested in their improved magnetic and electric properties. Mechanical attrition by high energy ball milling (HEBM) is a top down process for producing fine particles. However, fineness is associated with high surface area and hence is prone to oxidation which has a detrimental effect on the useful properties of these materials. Passivation of nanoparticles is known to inhibit surface oxidation. At the same time, coating polymer film on inorganic materials modifies the surface properties drastically. In this work a modified set-up consisting of an RF plasma polymerization technique is employed to coat a thin layer of a polymer film on Fe nanoparticles produced by HEBM. Ball-milled particles having different particle size ranges are coated with polyaniline. Their electrical properties are investigated by measuring the dc conductivity in the temperature range 10-300?K. The low temperature dc conductivity (I-V) exhibited nonlinearity. This nonlinearity observed is explained on the basis of the critical path model. There is clear-cut evidence for the occurrence of intergranular tunnelling. The results are presented here in this paper.     

Spectral restoration and energy resolution improvement of electron energy-loss spectra by Pixon reconstruction: II. Application to practical ELNES analysis of low SNR

We applied Pixon deconvolution as introduced in Part I to several practical, examples of low signal-to-noise ratio (SNR), electron energy-loss spectra with a goal toward restoring their fine spectral features and/or improving the energy resolution. We demonstrate that by directly fitting the two-dimensional spectral data recorded on the CCD; the method enables us to reveal fine spectral structures. Consequently, Pixon reconstruction extends the ability to probe electronic states in very spatially localized areas, a capability currently unique to our method.     

Surface durability of powder-forged roller treated by shot peening

To investigate the influence of shot peening on the surface durability of powder-forged rollers, the case-hardened powder-forged rollers with a forging density of 7.5 g/cm³ treated by the single shot peening and the double shot peening were fatigue-tested under a sliding-rolling contact condition. The surface roughness, the surface hardness and the surface compressive residual stress of the rollers were increased by the shot peening. In addition, the pores near the roller surface were deformed by the shot peening. The failure mode of all the test rollers was spalling due to subsurface cracking. The fatigue lives of all the test rollers were improved by the shot peening, and that of the test roller S08, which was shot-peened with the hardest steel shots in this experimental range, was especially improved. The surface durability of the test roller S08 was also most improved by the shot peening. Cracks became difficult to occur and propagate under the roller surface since the pores near the roller surface were deformed by the stronger shot peening. In this study, double shot peening, which generally restrains the increase in surface roughness, was not particularly effective for the improvement in the surface durability of the powder-forged rollers, because the influence of tangential force on fatigue was not always great in a case of subsurface cracking.     

Crystal growth and scintillation properties of Er-doped Lu3Al5O12 single crystals

Er-doped Lu₃Al₅O₁₂ (Er:LuAG) single crystalline scintillators with different Er concentrations of 0.1, 0.5, 1, and 3% were grown by the micro-pulling-down (μ-PD) method. The grown crystals were composed of single-phase material, as demonstrated by powder X-ray diffraction (XRD). The radioluminescence spectra measured under ²⁴¹Am α-ray excitation indicated host emission at approximately 350 nm and Er³⁺ 4f-4f emissions. According to the pulse height spectra recorded under γ-ray irradiation, the 0.5% Er:LuAG exhibited the highest peak channel among the samples. The γ-ray excited decay time profiles were well fitted by the two-component exponential approximation (0.8 μs and 6-10 μs).     

Pharmaceutical production of tableting granules in an ultra-small-scale high-shear granulator as a pre-formulation study

Objective: In some of drug developments, the amount of bulk drug powder to use in early stages is limited and it is not easy to supply a sufficient drug amount for conventional preparation methods. Therefore, an ultra-small-scale high-shear granulator (less than 5?g) (USG) was developed and applied to small-scale granulation as a pre-formulation. Method: The sample powder consisted of 66.5% lactose, 28.5% microcrystalline cellulose and 5.0% hydroxypropylcellulose. The granules were obtained to agitate 5?g of the sample powder with 1.0?mL of water at 300?rpm for 5?min after pre-powder mixing for 3?min by the USG and the manual hand (HM) methods. Results: The granules were evaluated by the 10% and 90% accumulated particle size and the recoveries of the granules and the powder solid. Median particle size for the USG and the HM methods was 159.2?±?2.3 and 270.9?±?14.9 μm, respectively. The USG method had a narrower particle size distribution than those by the HM method. The recovery of the granules by USG was significantly larger than that by the HM method. Conclusion: Characteristics of all of the granules indicated that the USG method could produce higher quality granules within a shorter time than the HM methods.