三羟甲基丙烷缩合工艺的研究

介绍了三羟甲基丙烷的缩合反应机理及在缩合反应中所发生的副反应，用反应动力学理论讨论了影响缩合反应的各种因素，并列出了在40L反应釜中所进行的缩合试验结果，提出了缩合的最佳工艺条件，结合国内外生产装置的实际，提出了采用最佳缩合工艺条件所需进行的改造措施，以有效地降低原料消耗和提高产品质量。     

喷射电沉积块体纳米晶Co-Ni合金工艺的研究

利用扫描电子显微镜（SEM），能谱仪（EDS）及X射线衍射（XRD）等分析方法研究了工艺参数对电解液喷射电沉积法制备块体纳米晶Co-Ni合金沉积层成分及结构的影响。结果表明；在本实验条件下，随电解液喷射速度的增加，沉积层中钴含量增加，而晶粒尺寸减小；随电解液温度的升高，沉积层中钴含量减小到一定值后增大，晶粒尺寸呈相反的趋势。沉积层的表面形貌为胞状结构。     

吡咯烷基-N-甲酸,丙烯酸乙二醇酯的合成及其光聚合动力学的研究

合成了不含氢键的低粘度的吡咯烷基-N-甲酸-丙烯酸乙二醇酯(PLW),并采用实时红外光谱法检测了光强和光引发剂浓度对光聚合动力学的影响。随着光强的增加光聚合的最终转化率基本不变,但是光聚合速率有明显的增加,并且达到最大聚合速率的时间也缩短。随着光引发剂浓度的增加,最终转化率和最大聚合速率都有了显著的增加。所合成单体的转化率在30 s内能达到90%以上。     

明胶和胶囊生产干燥新工艺的研究

本文介绍了氯化锂液体除湿的工作原 理,并深入分析了其除湿工艺、主要特点和在 明胶与胶囊干燥方面的研究和应用。     

UHMWPE混炼接枝马来酸酐研究

讨论了超高相对分子质量聚乙烯(UHMWPE)混炼接枝马来酸酐(MAH)过程中，单体MAH用量、引发剂DCP用量、交联抑制剂己内酰胺(CAILA)用量、流动改性剂硬脂酸钙(CaSt2)用量及混炼温度、时间等工艺条件对UHMWPE接枝率和凝胶含量的影响。用红外光谱表征了接枝物的存在。并用滴定分析法和重量分析法测定了接枝物UHMWPE～g～MAH的接枝率和凝胶含量。实验表明，MAH用量为5份、DCP为0．15份、CALA为0．1份、CaSt2为1份时。混炼温度175∽180℃。混炼时间14min时，可得到接枝率0．75％、凝胶含量1．48%的UHMWPE接枝物。     

水流掺气对明流泄洪洞及挑坎水力特性的影响

水流充分掺气可以避免高流速泄洪设施发生空蚀,但也会改变相关水力特性。通过对某大坝泄洪洞掺气设施水力模型试验及关于水流表面自掺气发生条件的相关分析,提出了在全程流速超过38 m/s,长度达550 m的明流洞内仅布置一级掺气设施的建议,较通常情况减少了两级;并针对泄洪洞出流方向与河道流向交角达60°的特点,研究提出了一种大差动异型鼻坎消能工。水工模型试验成果表明,其挑流水舌沿河道纵向扩散良好,水舌外缘与河道对岸保持了30 m以上的安全距离。该泄洪洞建成后经历了高水头、较长时间的泄洪运行,明流洞和鼻坎消能工均无空蚀发生,但挑坎水舌却冲刷到对岸边坡。     

化纤帆布标准组织规格的调整建议

分析现行化纤帆布行业标准中的不足，建议调整有关组织规格的规定，以促进帆布产品的性能提高。建议根据不同产品要求及实际生产情况，适当调整原料线密度和织编密度，以达到提高产品性能的目的。此外，在标准中增添织缩率项目要求以保证产品质量。     

Fischer-Tropsch Synthesis over Modified Cobalt Catalysts

The catalysts of Co/Zr-SiO2 were prepared by precipitation and the promoter of Pt was supported by impregnation. The reducibility of the cobalt oxide and the other physicochemical properties of the catalysts were characterized by TPR, TPD, BET and XPS. With the evaluation of the reduction temperature, the reduction degree increased but the surface area of the catalysts and the adsorption property for reactant CO distinctly decreased; The addition of Pt resulted in the improvement of the reducibility by decreasing the reduction temperature of cobalt oxide species. The FT-synthesis has been performed in a quartz fixed-bed reactor, and the experimental results showed that the best activity for promoted catalyst has been found at the reduction temperature of 400℃, in spite of its uncompleted reduction.     

高浊度微污染黄河水的处理工艺

在混凝处理中采用5%的清水回流与PAC+HPAM联合投加相结合的方法,形成高浊度微污染黄河水的处理工艺。应用该技术对高浊度水进行生产性试验,除浊效果与传统工艺相比约提高40%～50%,对有机物和NH3-N的去除率也有所提高,同时可使出水的致突变活性呈阴性。     

DMTO – a method for Discrete Material and Thickness Optimization of laminated composite structures

This paper presents a gradient based topology optimization method for Discrete Material and Thickness Optimization of laminated composite structures, labelled the DMTO method. The capabilities of the proposed method are demonstrated on mass minimization, subject to constraints on the structural criteria; buckling load factors, eigenfrequencies, and limited displacements. Furthermore, common design guidelines or rules, referred to as manufacturing constraints, are included explicitly in the optimization problem as series of linear inequalities. The material selection and thickness variation are optimized simultaneously through interpolation functions with penalization. Numerical results for several parameterizations of a finite element model of a generic main spar from a wind turbine blade are presented. The different parameterizations represent different levels of complexity with respect to manufacturability. The results will thus give insight into the relation between potential weight saving and design complexity. The results show that the DMTO method is capable of solving the problems robustly with only few intermediate valued design variables.