High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.     

Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.     

Chemical reaction kinetics dataset of Cs-I-B-Mo-O-H system for evaluation of fission product chemistry under LWR severe accident conditions

In order to improve LWR source term under severe accident conditions, the first version of a fission product chemistry database named ‘ECUME’ was developed. The ECUME is intended to include several datasets of major chemical reactions and their effective kinetic constants for representative severe accident sequences. It is expected that the ECUME can serve as a fundamental basis from which fission product chemical models can be elaborated for use in the severe accident analysis codes. The implemented chemical reactions in the first version were those for representative gas species in Cs-I-B-Mo-O-H system from 300 to 3000 K. The chemical reaction kinetic constants were evaluated from either literature data or calculated values using ab-initio calculations. The sample chemical reaction calculation using the presently constructed dataset showed meaningful kinetics effects at 1000 K. Comparison of the chemical equilibrium compositions by using the dataset with those by chemical equilibrium calculations has shown rather good consistency for the representative Cs-I-B-Mo-O-H species. From these results, it was concluded that the present dataset should be useful to evaluate fission product chemistry in Cs-I-B-Mo-O-H system under LWR severe accident conditions, where kinetics effects should be considered.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.     

Hydrogen‐bonding interaction between poly(ε‐caprolactone) and low‐molecular‐weight amino compounds

The specific interactions between several low‐molecular‐weight diamino compounds and poly(ε‐caprolactone) (PCL) have been investigated by FT‐IR. It was found that PCL and 3,3′‐diaminodiphenylmethane (3,3′‐DADPM) interact through strong intermolecular hydrogen bonds in the blend. Thermal and mechanical properties of PCL/3,3′‐DADPM blends were investigated by DSC and tensile measurements, respectively. The glass transition temperature of the blend increases while both the melting point and the elongation‐at‐break of the blend decrease with the increase of 3,3′‐DADPM content. Besides 3,3′‐DADPM, several other low‐molecular‐weight compounds containing two amino groups, such as o‐phenylenediamine or 1,6‐diaminohexane, were also added into PCL and the corresponding blend systems were investigated by FT‐IR and DSC. The effect of the chemical structure of the additives on the properties of PCL is discussed. © 2001 Society of Chemical Industry     

Reaction joining of SiC ceramics using TiB2-based composites

SiC ceramics were reaction joined in the temperature range of 1450–1800 °C using TiB₂-based composites starting from four types of joining materials, namely Ti–BN, Ti–B₄C, Ti–BN–Al and Ti–B₄C–Si. XRD analysis and microstructure examination were carried out on SiC joints. It is found that the former two joining materials do not yield good bond for SiC ceramics at temperatures up to 1600 °C. However, Ti–BN–Al system results in the connection of SiC substrates at 1450 °C by the formation of TiB₂–AlN composite. Furthermore, nearly dense SiC joints with crack-free interface have been produced from Ti–BN–Al and Ti–B₄C–Si systems at 1800 °C, i.e. joints TBNA80 and TBCS80, whose average bending strengths are measured to be 65 MPa and 142 MPa, respectively. The joining mechanisms involved are also discussed.     

Effect of chloride ions on leaching rate of chalcopyrite

The effect of chloride on chalcopyrite leaching has been investigated by performing batch leaching tests with three kinds of leaching solutions and using Hiroyoshi’s model, which suggests that a zone of rapid leaching exists between the critical potential (E_c, equilibrium redox potential for the reduction of CuFeS₂ to Cu₂S) and the oxidation potential (E_ox, equilibrium redox potential for the oxidation of Cu₂S). The results of the leaching tests show that the leaching rate in hydrochloric acid solution is the fastest and that the relationship between the Cu leaching rate and oxidation–reduction potential (ORP) follows Hiroyoshi’s model. Thermodynamic calculations indicate that, with an increase in the chloride concentration, the concentration of cuprous ions increases as the chlorocuprate(I) complex ions are formed and the contribution of cuprous ions to the critical potential is greater than that of cupric ions, even though the concentration of cuprous ions is lower than that of cupric ions. This fact suggests that the formation of chlorocuprate(I) ions in a chloride solution may improve the chalcopyrite leaching rate by increasing the critical potential.     

High‐current lightning discharges in winter

Lightning electric‐field waveforms related to power line faults in winter have been identified. Most of those waveforms appear to be associated with upward lightning discharges with absolute peak currents of over 100 kA. They are quite different from common return‐stroke waveforms, and the lightning discharges which produce these characteristic waveforms are called GC (Ground to Cloud) flashes. These high‐current lightning discharges are distributed around the coastline in different ways depending on their polarities. The spatial distributions of high‐current lightning discharges around Japan are also investigated. It is revealed that the region of Honshu Island along the coastline of the Sea of Japan belongs to the area in which the density of high‐current lightning flashes is the highest in Japan through the year. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 170(1): 8–15, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20874     

Effects of fermentation conditions and soybean peptide supplementation on hyaluronic acid production by Streptococcus thermophilus strain YIT 2084 in milk

To increase the hyaluronic acid (HA) yield from Streptococcus thermophilus YIT 2084, fermentation conditions (pH, temperature, agitation, aeration) were optimized in milk-based medium, and the effects of supplemental soybean peptides, which have different molecular weight distributions, were determined. HA production was enhanced to approximately 100 mg/l at pH 6.8 and 33–40 °C. Agitation speed and aeration rate slightly affected HA production. Soybean peptides including those of high molecular weight (approximately 27 to 130 kDa) further increased HA production to 208 mg/l under the optimal condition (pH 6.8, 35 °C, 100 rpm), which was 20-fold greater than non-optimal condition. HA production was no longer related to the specific growth rate. The HA produced under the optimal condition included a large amount of high-molecular-weight fraction of 100 to 2000 kDa, compared with under the basal condition without optimization.