营尔凹陷下白垩统油气勘探应避开高压水层

营尔凹陷下白垩统(K₁₎存在下沟组和赤金堡组2套源岩，目前它们已到成熟阶段。凹陷东侧长沙岭构造在下白垩统下沟组和赤金堡组储层中也发现油藏，但主要分布在高压水层的顶部及下部，而高压水层段存在良好的储层，并未发现油气。文章根据高压水层段的储层荧光特征，通过储层烃与源岩的对比，分析了下白垩统高压水层对油气运移的影响。研究结果表明：高压水层段，储层荧光弱，储层抽提物特征既不同于赤赤金堡组源岩，也不同于下构组源岩，为就近捕获的产物；高压水层未发生大规模的油气运移，其形成时间早于油气运移的时间。建议该区油气勘探目标的选择应避开高压水层，选择凹陷附近的圈闭、高压水层以下的层位。     

Laterally coupled buried heterostructure high-Q ring resonators

All-buried InP-InGaAsP ring resonators laterally coupled to bus waveguides are demonstrated. The buried configurations offer a lower built-in refractive index step along the resonator periphery, which affords enhanced optical coupling coefficients between the waveguides and reduced scattering losses caused by the resonator sidewall imperfections. Very low optical intensity attenuations of 0.4 cm/sup -1/ and coupling-limited quality factors of greater than 10/sup 5/ are observed from 200-/spl mu/m-radii ring resonators. The measured spectral linewidth is as narrow as 0.0145 nm.     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

选择测试阀在现场测试中的应用

选择测试阀是新一代全通径压控式测试器，在结构和性能上有了本质的创新，使现场操作更加简便、安全，对井筒条件要求低，更适用于高温、高压、深井、气井的地层测试，拓宽了地层测试和其它井下作业的兼容性。经7井次应用，其安全性、可靠性越来越得到认可。     

润滑油用纳米TiO2的表面改性及自修复性能研究

采用油酸对纳米TiO2进行表面改性，使其稳定分散于基础油中。利用HQ-1摩擦磨损试验机考察纳米TiO2的自修复性能，并探讨其自修复机理。试验结果表明，经改性后的纳米TiO2粉体作为润滑添加剂具有良好的分散稳定性、减摩抗磨性和自修复性。     

双层有机电致发光器件有机层厚度优化的数值研究

在陷阱电荷限制电流传导理论的基础上,提出了双层有机电致发光器件的数值模型,研究了结构为"阳极/空穴输运层(HTL)/发光层(EML)/阴极"的器件中电流密度和量子效率随有机层的特征陷阱能量、陷阱密度和载流子迁移率的依赖关系. 研究发现,对于给定的HTL和EML的特征陷阱能量、陷阱密度和载流子迁移率,存在一个最优的HTL和EML之间的厚度比率,在此最优厚度比下,器件的电流密度和量子效率达到最大.通过有机层厚度的优化,器件的电流密度和量子效率可提高多达两个数量级.另外,还研究了最优厚度比随有机层特征陷阱能量、总陷阱密度和载流子迁移率之间的定量关系.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

焊膏工艺性要求及性能检测方法

焊膏是SMT工艺中不可缺少的钎焊材料,广泛应用于再流焊中;它是由一定的合金粉末和助焊剂均匀混合而成的膏状体。主要对SMT中焊膏的组成及焊膏性能检测方法进行了简要分析。     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi