长输管线变电所备用电源自动投入系统的改造

根据管道储运公司下属的各变电所目前的运行方式以及备用电源自动投入系统(以下简称“备自投”)的运行情况，指出了备自投使用中的不足之处，并通过增加对应断路器的辅助触点来完善备自投，使变电所运行更加可靠。     

钢包炉(LF)预熔精炼渣的研究

预熔精炼渣具有成分均匀，性能稳定，储存时不吸水等特点，钢包炉中使用预熔精炼渣时成渣均匀且速度快，具有较强的吸附钢中非金属夹杂的能力。综合脱硫率高等冶金效果。有显著净化钢液作用。     

A high-resolution burst-mode laser transmitter with fast and accurate level monitoring for 1.25 Gb/s upstream GPONs

An innovative burst-mode laser transmitter (BM-TX) is presented for gigabit-capable passive optical network (GPON) upstream transmission at 1.25 Gb/s. The laser bias and modulation current each can reach 80 mA with a resolution of 0.1 mA providing a total drive current up to 160 mA. Both currents are generated by 10-bit current steering digital-to-analog converters (DACs), the architecture of which is specially adapted to yield a monotonic current setting at settling times below 12.8 ns. Tests show that fast automatic power control (APC) can stabilize and track the launched optical power with a tolerance of less than 1 dB over a wide temperature range for outdoor operation. The APC only requires a straightforward calibration of the "0" and the "1" level at room temperature. Optical level monitoring on strings of four consecutive "0" bytes and two consecutive "1" bytes at 1.25 Gb/s is demonstrated. APC based on such short strings of data has not been shown before. The circuits have been designed in a 0.35 /spl mu/m SiGe BiCMOS process. Experimental results show that this dc-coupled BM-TX meets the specifications of the recently approved ITU-T Recommendation G.984.2 supporting an intelligent power leveling mechanism (PLM).     

铸铝激光熔融处理后的组织与性能

应用光学和电子显微镜及显微硬度计研究了铸造Al-Si合金经激光表面熔融处理后的组织和性能。指出,组织分熔化区、过度区和基体三层。在熔化区中树枝状先共晶α相的平均宽度由原始组织的20～40μm细化到2～3μm,同时共晶组织也被大大细化。这些变化使显微硬度值由67.4提高至109～115.     

尺寸驱动的变参设计系统研究

本研究在简介国际上先进的变参设计几种方法及优点后,叙述了一个国家863/CIMS项目:CAD/CAPP/NCP集成系统中二维尺寸驱动的变参设计子系统的构成与功能;然后着重阐述了本系统采用的尺寸驱动的变参设计思想和几何约束建立的原则,并提供了系统数据结构,最后以几个实例证明了此方法的正确性与工程实用性。     

基于神经网络的模拟电路故障诊断优化近似方法

本文提出了线性电阻电路故障诊断的一种神经网络优化方法。其基本思想是应用Ｈｏｐｆｉｅｌｄ网络原理来处理Ｌ１范数问题，以此来进行诊断。对实例的计算证明此法是可行的。     

中高频小功率电子元器件用非晶材料的开发与应用

随着电力和电子技术的飞速发展，相应的元器件向高频化，小型化，高效率和节能的方向发展，从而对元器件用材料也提出了更高要求。为此，本文概述了冶金部钢铁研究总院近年来所研究的用于开关电源，脉冲变压器，传感器，电流互感器和电感器等方面的非晶软磁合金的性能及其应用概况。     

Soliton position jitter caused by periodic amplification andself-frequency shift

The formula for soliton timing jitter due to self-frequency shift and pulse width fluctuations caused by spontaneous-emission noise has been deduced. Such timing jitter is compared with that caused by the carrier frequency shift due to spontaneous-emission noise. It is shown that the timing jitter due to the self-frequency shift can be as large as the timing jitter due to carrier frequency shift when the total transmission distance is 100 times longer than the soliton period     

Accumulation and Mixing of Oils in Jinghu Sag of Subei Basin： Constraints from Thermal Maturity Parameters

Oils in Jinghu sag are abundant with high content of polar compounds and have a low ratio of saturate to aromatic hydrocarbons and a high ratio of resin to asphaltene. The gross composition of oils in the Jinghu sag suggests typical immature to low mature characteristics. Some compounds with low thermal stability were identified. Light hydrocarbons, a carbon preference index, an odd even index, n-alkane and hopane maturity parameters show mature features and little differences in the maturity level among oils. Sterane isomerization parameters indicate an immature to low mature status of oil. Transfer of the sedimentary center during sedimentation has led to different thermal histories among subsags and thus generated oils with different maturities. On the basis of source analyses, four migration and accumulation patterns with different maturity can be classified. Combined with available information on mergers of source, reservoir and long distance oil lateral migration, mixing conditions were present in the Jinghu sag. Experimental results indicate that maturity variations are caused by mixtures of hydrocarbons with different maturity.