The fuzzy logic-based modeling of a micro-scale sloped solar chimney power plant

Journal of Mechanical Science and Technology - The energy demand of world is increasing worldwide because of increasing population and developing technology. The use of environmentally friendly...     

Cost assessment of concrete and steel types for office buildings: An exploratory study

This paper presents a set of regression models which incorporates concrete and steel types in modeling the costs of office buildings. To these ends, three typical office buildings with seven and 15 stories have been designed by the help of a commercial software taking into account the Turkish practice. In each project C-16, C-20, C-25, C-30 and C-35 concrete classes and S-220 and S-420 steel types were used for dimensioning purposes. Rough construction costs were then calculated for different combinations of concrete classes and steel types. The findings of the study revealed that column dimensions decrease following an increase in a particular concrete class. However, this decrease stops after C-30. Furthermore, an average cost difference of 16% was observed between the steel types S-220 and S-420.     

Effect of weathering on the geomechanical properties of the Miocene basalts in Malatya,Eastern Turkey

Miocene volcanic rocks are widely exposed in the eastern Taurids, Turkey. The geomechanical properties and weathering degree of the Middle–Upper Miocene basalts were determined at the Boztepe dam site in Malatya, eastern Turkey. An engineering geology map of the Boztepe dam site was made and the joint sets and the degree of weathering determined in the field. The degree of weathering and RQD values were obtained on some 1,195 m of core which was then compared with a series of geomechanical tests including unit weight, porosity, water absorption, uniaxial compressive strength and compressive wave velocity. The geomechanical properties were compared with the weathering classifications of ISRM (Rock characterization, testing and monitoring, p 211, 1981) and Kilic (Environ Eng Geosci 4:475–483, 1999)      

Seepage failure by heave in sheeted excavation pits constructed in stratified cohesionless soils

In this study, experimental and numerical investigations are performed to clarify the seepage failure by heave in sheeted excavation pits in stratified cohesionless soils in which a relatively permeable soil layer (k_upper) lies above a less permeable soil layer (k_lower) between excavation base and wall tip. It is shown that the evaluation of base stabilities of excavation pits against seepage failure by using Terzaghi and Peck’s approach leads to considerably lower critical potential differences than those obtained from the model tests. On the other hand, a relatively good agreement is achieved between the results of the model tests and the finite element (FE) analyses. Further investigations are performed by using axisymmetric excavation models with various dimensions and ground conditions, and a comparison between the results obtained from Terzaghi and Peck’s approach and finite element analyses is given.     

Investigation of UV and I–V characteristics of high refractive index polymer thin film for optoelectronic applications

In this study, high refractive index polymer (HRIP) [poly(pentabromobenzyl methacrylate-co-glycidyl methacrylate)] was investigated to obtain its optical and electrical performance for optoelectronic applications. UV characteristics of the polymer in solution of tetrahydrofuran were obtained and optical band gap energy of the polymer was calculated as 3.8 eV. I–V characteristics of the polymer were investigated after HRIP thin film was prepared using spin coating technique. The electrical parameters such as barrier height Φ_Bo, ideality factor n and reverse saturation current I_o were extracted from the forward biasing I–V characteristics. At the same time, series resistance R_s and Φ_Bo were determined by using a modified Norde function combined with conventional forward I–V method.     

The elasto-plastic impact analysis of functionally graded circular plates under low-velocities

In this study, three-dimensional elasto-plastic analysis of functionally graded (FG) circular plates under low-velocity impact loads is presented. The FG circular plate is composed of ceramic (SiC) and metal (Al) phases, varying in a predetermined fashion through the plate thickness. The elasto-plastic behaviour of the FG circular plate is described by the TTO model. In the analyses, the ceramic phase is taken to be an isotropic elastic material whereas the metal phase is taken to be elasto-plastic material in accordance with the TTO model. The locally effective material properties were evaluated using homogenization method which is based on the Mori–Tanaka scheme. The effects of compositional gradient exponent and impactor velocity on the elasto-plastic impact response of the FG circular plates are investigated, and results are presented graphical form. The compositional gradient exponent and impactor velocity have significant effects on the elasto-plastic impact response of the FG circular plates. The elasto-plastic impact response of FG circular plates is similar to those of homogeneous plates. Therefore, the TTO model can be used to describe the mechanical behaviour of FG plates beyond the elastic range, assuming that the material response is essentially governed by the spreading of plasticity in the metal phase.     

Designing of a powder compressing device with vibration and investigation of compressibility of MgO powders with this device

One of metal matrix composite (MMC) production methods is infiltration of liquid metal into preformed reinforcement. In this method, MMCs are produced by infiltration of liquid metal into preformed reinforcement using one of pressure, vacuum or pressureless (free) infiltration methods. For infiltration purposes, reinforcement materials in different figuration are preformed in desired shape and reinforcement volume ratio. In this study a vibration apparatus has been designed to compress the particulate reinforcement in a tube so that pressure or vacuum infiltration can be carried out. The compressibility of MgO powders with different sizes with this apparatus has also been investigated. It has been found that with this apparatus, it is possible to compress desired number of specimens uniformly at the same time and at the same ratio. It has also been determined that MgO powders can be compressed in different ratio due to particle sizes with this device. Compressing time of 3 min is enough to reach maximum compression ratio in MgO powders.     

Effect of Ball Burnishing Treatment on the Fatigue Behavior of 316L Stainless Steel Operating Under Anodic and Cathodic Polarization Potentials

Corrosion fatigue (CF) behavior of AISI 316L was investigated in a 3 pct NaCl aqueous solution at an R = ? 1 stress ratio and a frequency of 60?Hz at room temperature. The test scale specimen was 7 cm². The passive (0 mV_Ref), pitting (120?mV_Ref), and cathodic (? 1400?mV_Ref) polarization potentials were statically applied and recorded during CF tests until the samples were broken. The shaft material surface was treated with a ball burnishing (BB) process. By the results, the fatigue behavior of AISI 316L was affected by polarization potential and surface treatment. Under 0?mV potential charged tests for 5?×?10⁵ cycles, BB treatment raised the CF strength of the shaft material from about 448 to 702?MPa with a percent 57 increase. Fractographic observations revealed that corrosion pits occurred during the experiments where anodic potential was applied and that transgranular surface fractures occurred in all cases.     

Investigation of using possibility of grape pomace in wafer sheet for wheat flour substitution

In this study, grape pomace (GP), a by-product consisting of grape skins and seeds rich in dietary fibres and polyphenols, was used in wafer sheets at different concentrations [5.00 (GP5), 10.0 (GP10), and 15.0 g 100 g⁻¹ (GP15)] for the partial replacement of wheat flour (WF) and improve the functionality of wafer sheets. The GP inclusion at concentrations higher than 5.00 g 100 g⁻¹ significantly affected the texture of sheets as well as the flow behaviour of batters, resulting in softer sheets and more viscous batters (P < 0.05). Moisture contents did not significantly change after GP addition (P > 0.05). After the addition of GP, the L* values decreased and the a* values increased, making the wafers darker (P < 0.05). Moreover, under simulated in vitro digestion conditions, the bioaccessibility of total phenolic compounds in saliva, gastric juice, and intestinal juice was significantly higher than control even at the lowest GP concentration (P < 0.05). Regarding sensory properties, only smoothness and crispness were significantly affected by GP addition, and samples were found to be crisper with higher concentrations of GP. In conclusion, it is possible to partially replace the WF in wafers with GP at a concentration of 5.00 g 100 g⁻¹ to develop a product with higher functionality and nutrient content.     

Control of Aspergillus flavus with essential oil and methanol extract of Satureja hortensis

The essential oil and methanol extract of Satureja hortensis were tested for antifungal activity against Aspergillus flavus in vitro on Petri plates and liquid culture, and under storage conditions. The oil showed strong antifungal activity based on the inhibition zone and minimal inhibitory concentration values against the pathogen on Petri plates assays. The very low concentrations of them also reduced wet and dry mycelium weight of pathogen fungus in liquid culture. When the oils at 25, 12.5 and 6.25 microl/mL concentrations were applied to lemon fruits before seven days of pathogen inoculation on storage conditions, the decay on fruits caused by the pathogen could be prevented completely. The results in this study showed that the essential oil of S. hortensis had strong antifungal activity against pathogen fungi tested. So, the essential oil of S. hortensis could be used for management of this pathogen as a potential source of sustainable eco-friendly botanical fungicides.