Formation of the spore clumps during heat treatment increases the heat resistance of bacterial spores

Effects of the clumping of bacterial spores on their heat resistance as a result of heat treatment were investigated. Spore suspensions of Bacillus cereus, Bacillus coagulans and Bacillus licheniformis were heated at 85 degrees C. Survivor curves of the three strains showed tailing in all treatments after 30 min. As the treatment time increased, the formation of spore clumps increased in all strains after 20 min. Relative hydrophobicity of the spore surface increased as a result of heat treatment. The effect of spore concentration on the inactivation of the B. licheniformis spores was investigated, and surviving curves showed no tailing below a concentration of 4.9 log CFU/ml.     

Breakup of non-newtonian emulsion jets

The breakup of non-Newtonian emulsion jets into drops was experimentally studied by ejecting both O/W and W/O emulsions vertically downward into stagnant air through nozzles. Breakup lengths of non-Newtonian emulsion jets were found to be almost equivalent to those of Newtonian jets. Experimental breakup data establish that the static surface tension of the oil phase can be used as the surface tension of W/O emulsion jets, whereas the dynamic surface tension of aqueous surfactant solutions is used as that of O/W emulsion jets. Diameters of drops formed from non-Newtonian emulsion jets are in good agreement with the prediction from the stability theory previously developed by the authors. When the rheological index in a power law model is appreciably smaller than unity and the Ohnesorge number is significantly large, however, drop sizes are larger than the prediction because of the profile relaxation in jets. The critical velocity of emulsion jets, either O/W or W/O emulsion, is significantly lower than that of homogeneous Newtonian jets.     

A collection of parallel linear equations routines for the Denelcor HEP

This paper describes the implementation and performance results for a few standard linear algebra routines on the Denelcor HEP computer. The algorithms used here are based on high-level modules that facilitate portability and perform efficiently in a wide range of environments. The modules are chosen to be of a large enough computational granularity so that reasonably optimum performance may be insured. The design of algorithms with such fundamental modules in mind will also facilitate their replacement by others more suited to gain the desired performance on a particular computer architecture.     

Effect of heat treatment temperature on the microstructure and actuation behavior of a Ti–Ni–Cu thin film microactuator

Ti–Ni–Cu/SiO₂ two layer diaphragm-type microactuators were fabricated by sputter deposition and micromachining. The influence of heat treatment temperature on the actuation behavior was investigated under quasi-static conditions. The interfacial structure of Ti–Ni–Cu/SiO₂ and internal structure of the Ti–Ni–Cu layer were also investigated using transmission electron microscopy. The reaction layer formed between the Ti–Ni–Cu and SiO₂ layers, and preferentially grew into the SiO₂ side. The reaction layer formed at 1023 K mainly consisted of Ti₄(Ni,Cu)₂O. The maximum height of the diaphragm decreased with increasing heat treatment temperature. The growth of the reaction layer also affected the microstructure of the Ti–Ni–Cu layer. The density of fine platelets and Ti₂Ni precipitates decreased with increasing heat treatment temperature from 873 to 923 K, and they disappeared at 973 K due to the fact that the reaction layer mainly consisted of a Ti-rich phase. The microactuator heat treated at 973 K showed the highest transformation temperature with the lowest transformation temperature hysteresis, which is attractive for high speed actuation.     

Determination of fracture toughness of human permanent and primary enamel using an indentation microfracture method

The purpose of the present study was to examine the fracture toughness and Vickers microhardness number of permanent and primary human enamel using the indentation microfracture method. Crack resistance and a parameter indirectly related to fracture toughness were measured in 48 enamel specimens from 16 permanent teeth and 12 enamel specimens obtained from six primary teeth. The Vickers microhardness number of the middle portion was greater than the upper portion in primary enamel. The fracture toughness was highest in the middle portion of permanent enamel, because fracture toughness greatly depends upon microstructure. These findings suggest that primary teeth are not miniature permanent teeth but have specific and characteristic mechanical properties.     

Structural features of anodic oxide films formed on aluminum substrate coated with self-assembled microspheres

The structural features of anodic oxide films formed on an aluminum substrate coated with self-assembled microspheres were investigated by scanning electron microscopy and atomic force microscopy. In the first anodization in neutral solution, the growth of a barrier-type film was partially suppressed in the contact area between the spheres and the underlying aluminum substrate, resulting in the formation of ordered dimple arrays in an anodic oxide film. After the subsequent second anodization in acid solution at a voltage lower than that of the first anodization, nanopores were generated only within each dimple. The nanoporous region could be removed selectively by post-chemical etching using the difference in structural dimensions between the porous region and the surrounding barrier region. The mechanism of anodic oxide growth on the aluminum substrate coated with microspheres through multistep anodization is discussed.     

The influence of proteins on the fretting-corrosion behaviour of a Ti6Al4V alloy

The effects of collagen and albumin on the fretting-corrosion behaviour of a Ti6Al4V alloy contacting an Al₂O₃ counter-piece was investigated in pH buffered saline solutions at 37 °C using a tribo-electrochemical apparatus. Phosphate ion and hydroxyethyl-piperazinyl-ethanesulfonic acid (HEPES) were used as the pH buffer agents. Tests were conducted under two applied electrochemical potentials and two loads. Potentiodynamic polarisation curves were measured to assess the effect of proteins and pH buffer agents on the corrosion behaviour. Surfaces were characterised by XPS analysis, secondary electron spectroscopy and laser profilometry.Fretting wear of the Ti6Al4V alloy increased with increasing applied potential and load but was not significantly affected by the presence of collagen or albumin. Only a small lubricant effect of collagen could be observed at cathodic potentials. In phosphate buffer saline (PBS) solutions, those proteins were found to act as cathodic inhibitor by shifting the corrosion potential and the cathodic current towards more cathodic values. Phosphate ions were found to be incorporated on the Ti6Al4V alloy and to cause sedimentation of wear particles around the wear trace. In HEPES solutions wear particles were dispersed away from the wear trace.     

Preparation and biological evaluation of hydroxyapatite-coated nickel-free high-nitrogen stainless steel

Calcium phosphate was formed on nickel-free high-nitrogen stainless steel (HNS) by chemical solution deposition. The calcium phosphate deposition was enhanced by glutamic acid covalently immobilized on the surface of HNS with trisuccinimidyl citrate as a linker. X-ray diffraction patterns and Fourier transform infrared spectra showed that the material deposited on glutamic acid-immobilized HNS within 24 h was low-crystallinity calcium-deficient carbonate-containing hydroxyapatite (HAp). The biological activity of the resulting HAp-coated HNS was investigated by using a human osteoblast-like MG-63 cell culture. The HAp-coated HNS stimulated the alkaline-phosphate activity of the MG-63 culture after 7 days. Therefore, HAp-coated HNS is suitable for orthopedic devices and soft tissue adhesion materials.