The desalting and recycling of wastewaters from textile dyeing operations using reverse osmosis

The wastewater from the textile dyeing operations was separated into a concentrate stream, rich in salts and dyes, and a purified product water stream using reverse osmosis membranes. Three membrane materials and three module configurations were used, namely : polyamide (hollow fine fiber configuration ), cellulose acetate ( spiral wound and tubular configurations ) and hydrous Zr(IV)- polyacrylate ( tubular configuration ). The modules were tested for periods ranging from 600 hours to more than 1000 hours under actual field conditions. Membrane flux and rejection were monitored throughout the operation and samples of the feed and product water were analysed chemically. The successful operation of the R.O. equipment under field conditions demonstrated the applicability of this process in the desalination of dyeing wastewater.     

Thermal decomposition behavior of γ‐irradiated poly(vinyl acetate)/poly(methyl methacrylate) miscible blends

Miscible polymer blends based on various ratios of poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) were prepared in film form by the solution casting technique using benzene as a common solvent. The thermal decomposition behavior of these blends and their individual homopolymers before and after γ‐irradiation at various doses (50–250 kGy) was investigated. The thermogravimetric analysis technique was utilized to determine the temperatures at which the maximum value of the rate of reaction (T_max) occurs and the kinetic parameters of the thermal decomposition. The rate of reaction curves of the individual homopolymers or their blends before or after γ‐ irradiation displayed similar trends in which the T_max corresponding to all polymers was found to exist in the same position but with different values. These findings and the visual observations of the blend solutions and the transparency of the films gave support to the complete miscibility of these blends. Three transitions were observed along the reaction rate versus temperature curves; the first was around 100–200°C with no defined T_max, which may arise from the evaporation of the solvent. The second T_max was in the 340–380°C range, which depended on the polymer blend and the γ‐irradiation condition. A third transition was seen in the rate of reaction curves only for pure PVAc and its blends with PMMA with ratios up to 50%, regardless of γ‐ irradiation. We concluded that γ‐irradiation improved the thermal stability of PVAc/PMMA blends, even though the PMMA polymer was degradable by γ irradiation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1773–1780, 2006     

Strength and Microstructure of Silicon Nitride Ceramics Brazed with Nickel-Chromium-Silicon Alloys

Joining of sintered Si₃N₄ was performed using a high-temperature brazing technique. Ni-based brazing alloys having the same Ni:Cr ratio as AWS BNi-5 (Ni·18Cr·19Si (at. %)) but different Si content were used as the brazing filler metals. Joining experiments were performed at 1220°C under a N₂ partial pressure of 15 Pa for different times between 5 to 15 min. The highest room-temperature four-point bend strength of the joints was 115 MPa, whereas 220 MPa was achieved when the joints were tested at 900°C. The high strength of the experimental joints was attributed to the reduction in residual stresses and formation of a CrN reaction layer at the ceramic/filler metal interface.     

Kinetic study of radical polymerization. II. Solid‐state bulk polymerization of sodium methacrylate by differential scanning calorimetry

The solid‐state radical polymerization of sodium methacrylate was investigated. It was initiated by azobisisobutyronitrile, which was used as a radical initiator. Differential scanning calorimetry (DSC) was used to observe the endothermic and exothermic transitions during the polymerization reaction. Structural studies were performed with the DSC thermograms and Fourier transform infrared and ultraviolet–visible spectra, and all of the results confirmed the progress of the reaction. The obtained data revealed that the polymerization reaction proceeded completely with a 100% conversion. ΔH of this reaction was calculated with various amounts of the initiator, and the peak temperatures were determined at different heating rates. The activation energy (19.7 kcal mol^?1) was also obtained by the Kissinger method for this type of solid polymerization reaction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1648–1654, 2003     

Synthesis of copolymers of tert‐butyl vinyl ether with maleic and citraconic anhydrides

In the present study, the effects of charge‐transfer complex formation and intramolecular fragmentation (side‐chain lactonization) in radical copolymerization of tert‐butyl vinyl ether (t‐BVE) with anhydrides of maleic (MA) and citraconic (CA) acids and the structure–thermal behavior relationships of the resulting copolymers were examined using the ¹H‐NMR, FTIR, DSC, and TGA analysis methods. It was shown that copolymerization under the chosen conditions proceeded through intramolecular fragmentation with the formation of γ‐lactone units. Side‐chain fragmentation of t‐BVE–MA and t‐BVE–CA copolymers also was confirmed by TGA and DSC analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2455–2463, 2006 2006     

Thermal characterization of n‐alkyl maleate‐styrene‐allyl propionate terpolymers

Thermal characterization of maleic anhydride‐styrene‐allyl propionate (MA‐St‐AP) terpolymer and its ester derivatives named as n‐alkyl maleate and shown as nPr MA‐St‐AP, nBu MA‐St‐AP, nPn MA‐St‐AP, and nBz MA‐St‐AP was carried out. The thermal characterization was performed using thermal analysis techniques such as TGA, DTA, DSC, and TMA. Different results were observed between the original terpolymer and its ester derivatives. Thermal stabilities of the terpolymer and its ester derivatives were compared by using various measurements plotted as TGA, DTA, DSC, and TMA curves. The increase in the alcohols' carbon numbers added to the original terpolymer results in ester derivatives with different thermal stability behavior. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 600–604, 2007     

Synergic influence of a surfactant and ultrasonication on the preparation of soluble,conducting polydiphenylamine/silica‐nanoparticle composites

Conducting polydiphenylamine was used to encapsulate silica nanoparticles through the oxidative polymerization of diphenylamine in the presence of ultrasonic irradiation. The polymerization was performed in the presence of sodium lauryl sulfate as a surfactant. Experiments performed in the absence of ultrasound clearly demonstrated that the application of ultrasonication played multiple roles in the preparation of a composite of polydiphenylamine with silica nanoparticles. Ultrasonication dispersed the silica nanoparticles, converted sodium lauryl sulfate to lauryl alcohol, and augmented the dispersion of the silica‐nanoparticle/polydiphenylamine composite in an organic medium. Silica‐nanoparticle/polydiphenylamine composites were also prepared in the absence of ultrasound and/or sodium lauryl sulfate. The silica‐nanoparticle/polydiphenylamine composites were characterized with Fourier trans form infrared spectroscopy, ultraviolet–visible/near‐infrared spectroscopy, and thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3912–3918, 2006     

Electrodeposition of smooth and adherent film of polypyrrole on lead electrode

Electropolymerization of pyrrole on lead substrate electrode was studied. Due to electrochemical activity of Pb in acidic media, this process is only possible at basic pHs. For this purpose, electropolymerization process was performed in an aqueous solution of Na₂SO₄ with pH 12. Potentiodynamic cycling shows the Pb oxidation at the first cycles. In subsequent cycles, polypyrrole film grows on the oxidized lead substrate. Of course, as the passive film is highly porous, a composite of polypyrrole/PbSO₄ is formed in the first layers. However, subsequent cycling leads to the formation of pure polypyrrole film. According to this structure and strong connection of the polymer film to the substrate surface via this composite layer, the polypyrrole film deposited on the lead surface has enhanced mechanical stability. AFM measurements showed peculiar smoothness of both composite and lateral polypyrrole films. This synthesis approach is of particular interest for the preparation of highly stable polymer films and fabrication of supercapacitors with a polymer/PbSO₄ conductive structure.     

尿素嵌入法制备纤维素氨基甲酸酯的研究

探讨了尿素嵌入法制备纤维素氨基甲酸酯(CC)的生产工艺。指出:选用聚合度为450~625、α-纤维素含量大于90/的纤维素浆粕,用14/~16/的氢氧化钠溶液,于40~50℃条件下活化处理30~40min后,与尿素以1∶2~3的比例混合,在137℃的二甲苯体系中反应2~3h,便可得到含氮量为2.4/~3.5/的纤维素氨基甲酸酯产物。该产物在氢氧化钠溶液中可形成良好的稳定溶液,过滤性好,可直接用于纺丝。     

Investigation of the effects of fatty acids on the compressive strength of the concrete and the grindability of the cement

In cement industry, a great energy consumption has been observed during grinding of clinker. To reduce this consumption, some waste products have been used as grinding aids.In this investigation, the effects of sunflower oil (SO), oleic acid (OA), stearic acid (SA), myristic acid (MA) and lauric acid (LA) on the fineness and strength of the cement have been examined. These aids were added into clinker in certain ratios based on the cement clinker weight and the grinding has been done for a definite time at the same condition.All of the fatty acids used increased the fineness as compared with the cement without the grinding additives. SO and OA decreased the strength significantly, LA decreased it to a lesser extent and SA increased it definitely according to the common cement. But MA did not alter the strength of the cement as much as SA. In addition, the covering of the balls influences the grinding of cement clinker unfavourably.