Numerical modeling of near corona wire electrohydrodynamic flow in a wire-plate electrostatic precipitator

Numerical modelling of the flow velocity fields for the near corona wire electrohydrodynamic (EHD) flow was conducted. Solutions of the steady, two-dimensional momentum equations have been computed for a wire-plate type electrostatic precipitator (ESP). The equations were solved in the conservative finite-difference form on a fine uniform rectilinear grid of sufficient resolution to accurately capture the momentum boundary layers. The numerical procedure for the differential equations was used by SIMPLEST algorithm. The CFD code coupled with Poisson's electric field, ion transport equations and the momentum equation with electric body force, was used for the numerical simulation with the Chen-Kim k-epsiv turbulent model. The numerical results show that EHD secondary flow was clearly visible in the downstream regions of the corona wire despite the low Reynolds number for the electrode (Re _cw=12.4). Secondary flow vortices caused by the EHD increases with increasing discharge current or EHD number, hence pressure drop of ESP increases     

Finite element analyses of repaired articular surfaces.

The response to a compressive load of a repaired cartilage surface, consisting of full-thickness repair tissue adjacent to normal cartilage, was predicted by the u-p finite element method and compared to that of a normal cartilage surface under the same loading conditions. By individually varying the aggregate modulus, permeability and Poisson's ratio for the repair tissue, analyses were performed to assess the contributions of each to the changes in mechanical behaviour. In comparing the repaired to normal surfaces, the presence of a softer repair tissue resulted in increased axial and decreased radial deformations at any given time point, while a repaired surface with an increased permeability compressed more easily due to the increased fluid flow and caused equilibrium to occur sooner. For smaller Poisson's ratio, the axial deformation was not different from normal if the aggregate modulus was the same as normal; however, the radial expansion was reduced as the repair tissue experienced a larger volume change. These results indicate that the presence of repair tissue in a joint surface can have a strong influence on the mechanical behaviour of the surface.     

Phase behavior of polycarbonate blends with selected halogenated polymers

Bisphenol A polycarbonate is shown to be miscible with a vinylidene chloride based polymer containing 13.5% by weight of vinyl chloride. On the other hand, polycarbonate is found to be immiscible with poly(vinyl chloride), poly(vinylidene fluoride), and polyepichlorohydrin.     

In situ polyurethane/silica composite formation via a sol‐gel process

Polyurethane acrylate anionomer (PUAA)/silica composite gels were prepared by the sol‐gel reaction of tetraethoxysilane (TEOS) and methacryloxypropyl trimethoxysilane (MPTS) incorporated to PUAA gels by using a swelling method. The formation and structure of composites were confirmed by FTIR, X‐ray diffraction, and SEM. As a result, we found that silica components in composites are located within the ionic domains of their gels and interacted with PUAA via hydrogen bonding. This drastically enhanced the mechanical properties of the composites. Mechanical properties are also improved by MPTS, because MPTS improves the dispersibility and adhesion of silica components in PUAA/silica composite gels. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2327–2334, 2002     

Droplet de-entrainment by inertial impaction on vertical rods in an air-droplet mixture flow

We experimentally investigate the de-entrainment of droplets by inertial impaction on an array of vertical rods in an air-droplet mixture flow. The de-entrainment efficiencies are measured for a single rod, for a single row of rods, and for a multi-row of rods. We investigate the effects of the droplet mass flux (0.5–5.4 kg/m² s), the droplet Weber number (3000–8000), the air velocity (0–6 m/s), the rod geometry, and the surface roughness on the de-entrainment, and the rod diameter-to-pitch ratio effect on the de-entrainment. The results for a single rod show that the de-entrainment efficiency decreases slightly as the droplet mass flux increases; however, in our experimental ranges, there is negligible dependence on the droplet Weber number, the air velocity, and the surface roughness. The rod geometry affects the de-entrainment efficiency. The results for a single row of rods show that the existence of neighboring rods promotes de-entrainment due to droplet splashing, and we develop a correlation to show the effect of diameter-to-pitch ratio on the de-entrainment. Using information on the de-entrainment efficiencies of a single rod and those of a single row of rods, we propose a correlation that predicts the de-entrainment efficiency for a multi-row of rods with a staggered array. The RMS errors of the correlation from the de-entrainment efficiencies experimentally obtained are within 13.5%.     

Experimental observations on flow characteristics in an open two-phase natural circulation loop

The flow behavior in an open two-phase natural circulation loop was studied experimentally using Freon-113. The heat flux, inlet- and exit-restrictions, liquid charging level and inlet subcooling were taken as parameters. As a result, three basic circulation modes were observed with variation of the heat flux: periodic circulation (A), continuous circulation, and periodic circulation (B). Of these modes, only the continuous circulation mode was stable and the maximum circulation rate appeared with this mode. An increase in the inlet-restriction and/or decrease in the exit-restriction broadened the range of the continuous circulation mode and stabilized the system. When the liquid charging level was lowered or the inlet subcooling was decreased, the continuous circulation mode started at a lower heat flux and the system became stable. The results are summarized on instability maps in the plane of heat flux vs. inlet subcooling.     

Decision-directed maximum-likelihood estimation of OFDM framesynchronisation offset

The authors propose a method to estimate the synchronisation offset for orthogonal frequency division multiplexing (OFDM) frame alignment without resort to pilot tones. A decision-directed maximum-likelihood estimation of frame synchronisation offset is derived, and the performance of the proposed scheme is confirmed by computer simulation for QAM systems     

Modeling the I-V characteristics of fully depleted submicrometerSOI MOSFET's

In this paper, an analytic current-voltage model for submicrometer fully-depleted (FD) silicon-on-insulator (SOI) MOSFET's is presented. This model takes into account the source/drain series resistances which can be especially high in thin film SOI devices. The effect of drain induced conductivity enhancement is also included, which is important for submicrometer channels. The model is verified by comparison to measured SOI I-V characteristics. Good agreement is obtained for SOI film thicknesses ranging from 40 to 220 nm and effective channel lengths down to 0.25 μm     

A quadruple well, quadruple polysilicon BiCMOS process for fast 16Mb SRAM's

An advanced, high-performance, quadruple well, quadruple polysilicon BiCMOS technology has been developed for fast 16 Mb SRAM's. A split word-line bitcell architecture, using four levels of polysilicon and two self-aligned contacts, achieves a cell area of 8.61 μm² with conventional I-line lithography and 7.32 μm² with I-line plus phase-shift or with deep UV lithography. The process features PELOX isolation to provide a 1.0 μm active pitch, MOSFET transistors designed for a 0.80 μm gate poly pitch, a double polysilicon bipolar transistor with aggressively scaled parasitics, and a thin-film polysilicon transistor to enhance bitcell stability. A quadruple-well structure improves soft error rate (SER) and allows simultaneous optimization of MOSFET and bipolar performance