The onset of vortex instability in laminar forced convection flow through a horizontal porous channel

The onset of convective instability in a fluid-saturated porous layer between the two horizontal plates heated isothermally from below has been analyzed theoretically by using propagation theory. In the analysis the thermal dispersion coefficient is assumed to be proportional to the streamwise velocity. The results show that both inertia and thermal dispersion stabilize the system.     

Nondestructive evaluation of the characteristics of degraded materials using backward radiated ultrasound

The frequency dependency of Rayleigh surface wave is investigated indirectly by measuring the angular dependency of the backward radiation of the incident ultrasonic wave in two kinds of degraded specimens by scuffing or corrosion. Then, the frequency dependency is compared with the residual stress distribution or the corrosion-fatigue characteristics for the scuffed or corroded specimens, respectively. The width of the backward radiation profile increases with the increase of the variation in residual stress distribution for the scuffed specimens. In the corroded specimens, the profile width decreases with the increase of the effective aging layer thickness and is inversely proportional to the exponent, m, in the Paris’ law that can predict the crack size increase due to fatigue. The result observed in this study demonstrates high potential of backward radiated ultrasound as a tool for nondestructive evaluation of subsurface gradient of material degradation generated by scuffing or corrosion.     

Effects of extended dislocations on charge distribution in GaN epilayer

We have investigated the effect of extended dislocations (0.5-3 μm) on charge distribution in GaN epilayer grown by metalorganic chemical vapor deposition on (0001) sapphire using atomic force microscopy (AFM) and scanning surface potential microscopy (SSPM). It has been observed for the surface at the extended dislocations present in undoped GaN film to be negatively charged showing 0.04-0.2 V higher potential relative to regions that contain no dislocations. In addition to the higher potential at the dislocation core, the surrounding surfaces, including the edge of the dislocations, are also negatively charged in a symmetric way around the dislocations revealing crater-shaped higher potential regions (∼0.04 V) relative to surrounding dislocation-free area. The experimental results show that the protrusion-type of dislocation is also negatively charged and its potential is dependent on the size of dislocation.     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure     

Efficient and stable field emission from the oxidized porous polysilicon using Pt/Ti multilayer electrode

The field emission characteristics of an oxidized porous polysilicon (OPPS) were investigated with a Pt/Ti multilayer electrode, which showed highly efficient and stable electron emission characteristics compared with those of conventional Au/NiCr electrodes. The thin Ti layer played an important role in promoting the adhesion of Pt to SiO₂ surface and the distribution of the electric field on the OPPS surface. Additionally, the Ti layer efficiently blocked the diffusion of emitter metal, which resulted in more reliable emission characteristics.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Broadly wavelength-tunable external cavity lasers with extremely low power variation over tuning range

Tunable external-cavity lasers with low power variation over a broad tuning range are demonstrated using asymmetric multiple quantum-wells with a wide and flat gain. For a 2.8-/spl mu/m-wide ridge waveguide laser of cavity length 380 /spl mu/m, when used in a grating external cavity and with an antireflection coating on one facet of laser diode chip, the power variation of less than -1 dB is obtained over a range of 80 nm. This extremely low power variation is a direct result of the spectrally flat gain.     

Synthesis and characterization of a series of star-branched poly(ε-caprolactone)s with the variation in arm numbers and lengths

A series of star-branched poly(ε-caprolactone)s (SPCLs) was synthesized with structural variation of the arm numbers and lengths through ring-opening polymerization under bulk condition. Arm numbers were varied to be 3, 4, and 6 by using multifunctional initiating cores such as trimethylol propane, pentaerythritol, and dipentaerythritol, respectively. The lengths of the poly(ε-caprolactone) arms were varied by controlling the molar ratio of monomer-to-initiating hydroxyl group molar ratio ([CL]₀/[-OH]₀=5, 10, 15). Molecular weights were determined by both ¹H NMR end-group analysis and MALDI-TOF mass spectrometry, which gave reasonably consistent values. On the contrary, the GPC method failed to give accurate values of molecular weight of SPCLs due to the discrepancy with the linear standard. The branching architecture of SPCLs was evaluated by the branching ratio, g, which is the ratio of the mean-square radius of SPCL to that of liner counterpart, linear poly(ε-caprolactone) (LPCL), which is of the same chemistry and having the same molecular weight. The radii of gyration of SPCLs and LPCLs were determined using small-angle X-ray scattering (SAXS) from the initial slopes of Zimm plots, represented as 1/I(q) vs q² with I(q) and q being the scattered intensity and scattering vector, respectively. The g values were observed to decrease with increasing arm numbers, indicating more compact molecular structure for SPCLs with higher arm numbers, while no such effect was observed for arm length variation. Thermal properties as well as the degree of crystallinity of SPCLs were found to be also dependent on structural variations. The melting points and the degradation temperatures were observed to increase with increasing arm lengths but with constant arm number. On the other hand, arm number variation with constant arm length gave no such changes to the thermal transitions of SPCLs. However, for the SPCLs with equivalent molecular weights, the degree of crystallinity was found to decrease with increasing arm numbers.