Estimation of Limit Energy Characteristics of Volumetric Pneumatic Motors Taking into Account the Process Dynamics in Working Chambers

A methodology for estimation of the limit energy characteristics of volumetric pneumatic motors based on the Parameter Space Investigation method and a generalized mathematical model in dimensionless (normalized) form taking into account the dynamics of working processes is proposed. A calculated example is presented. The methodology is applicable for determination of the limit energy characteristics of newly created design solutions, of prospects to improve the known designs of pneumatic motors, of evaluation of energy capacity of several pneumatic motors supplied from a single source of compressed air, and of the initial data preparation for parametric synthesis of rotational pneumatic drives for two or more robots taking into account their interaction.     

Microwave dielectric properties of ultra-low loss Li2MgTi0.7(Mg1/3Nb2/3)0.3O4 ceramics sintered at low temperature by LiF addition

In this work, ultra-low loss Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics were successfully prepared via the conventional solid-state method. X-ray photoelectron spectroscopy (XPS), thermally stimulated depolarization current (TSDC) and bond energy were used to determine the distinction between intrinsic and extrinsic dielectric loss in (Mg_1/3Nb_2/3)⁴⁺ ions substituted ceramics. The addition of (Mg_1/3Nb_2/3)⁴⁺ ions enhances the bond energy in unit cell without changing the crystal structure of Li₂MgTiO₄, which results in high Q·f value as an intrinsic factor. The extrinsic factors such as porosity and grain size influence the dielectric loss at lower sintering temperature, while the oxygen vacancies play dominant role when the ceramics densified at 1400?°C. The Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics sintered at 1400?°C can achieve an excellent combination of microwave dielectric properties: ε_r =?16.19, Q·f?=?160,000?GHz and τ_f =??3.14?ppm/°C. In addition, a certain amount of LiF can effectively lower the sintering temperature of the matrix, and the Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄-3?wt% LiF ceramics sintered at 1100?°C possess balanced properties with ε_r?=?16.32, Q·f?=?145,384?GHz and τ_f =??16.33?ppm/°C.     

Conveyer-belt accidents in mining and metallurgy

The dynamic interaction between the mechanical and electrical drive parameters when damage suddenly appears in the mechanical part of a conveyer belt is investigated. The possibility of using the change in the motor’s electrical parameters as a diagnostic signal is assessed. A model for investigating the dynamic processes in the system consisting of the grid, the induction motor, and the conveyer belt is proposed. The grid and induction motor are described by a model of fourth-order state space, whose output is the torque at the motor shaft. The moments of inertia and pliability of the links between the elements in the mechanical part of the conveyer belt are determined. By gradually identifying the elements with the minimum moment of inertia and distributing their moments of inertia and pliabilities among the adjacent elements, we obtain a three-mass system simulating the mechanical part of the conveyer belt. This dynamic model is solved by means of Matlab Simulink software. The energy characteristics of the drive are determined in dynamic processes following a mechanical accident.     

Appraisal of Agriglass in Promoting Maize Production Under Abiotic Stress Conditions

An agriglass composition containing different oxides acts as a slow release for macro and micro nutrients and was chosen to improve maize yield under most important abiotic stresses which affecting agriculture development; salinity and drought. A field experiment was performed in salt affected soil (EC =?7.5 dSm^??1) by using different water deficit rates (I1 = 100, I2 = 85 and I3 = 70% of maize water requirements). Irrigation levels were located in main plots. Every main-plot divided into six sub-plots contained glassy fertilizer treatments [F1 = 55 kg fed^?1 with 1/2 mm diameter of agriglass (fed. =?4200 m²), F2 = 55 kg fed^?1 with 1 mm diameter, F3 = 80 kg fed^?1 with 1/2 mm diameter, F4 = 80 kg fed^?1 with 1 mm diameter, F5 = Recommendations of Ministry of Agriculture and F6 = control]. The experimental results demonstrated that, ears, straw, grains and biological yields increased with increasing both water and agriglass rates. Application of agriglass as a slow release fertilizer improved yield more than mineral fertilizer. Some growth parameters, water use efficiency (IWUE), macronutrients concentration and their relations were included. Other studies on residual effect of agriglass and the annual application rates to withstand salinity and drought stress by strategic crops are required.     

Analysis of ventilation of working areas in thick gently dipping coalbeds

Advanced technologies and modern high-production machines for underground mining of thick gently dipping coal demand strict adherence to technological discipline, reduction in operational loss and selection of optimized ventilation modes. The authors analyze ventilation schemes used in working areas in thick gently dipping seams in order to reveal influence exerted by the schemes, methods and parameters of ventilation on distribution of air loss in mined-out areas.     

Effect of ZnO layer thickness upon optoelectrical properties of NiO/ ZnO heterojunction prepared at room temperature

In this work, p-NiO/n-ZnO heterostructures were successfully prepared at room temperature using RF sputtering technique. The influence of ZnO layer thickness on the performance of the heterojunction was investigated. The deposited ZnO layers have a hexagonal Wurtzite structure with preferable growth orientations along (002) and (103) for thinner films. Increasing the thickness results in more crystallographic orientation randomness. The current–voltage measurements of the realized heterojunctions showed a clear rectifying behavior. The measured ideality factor varies from 2.5 to 1.6 according to the thickness of ZnO layer. The series resistance of the device is enlarged with increasing ZnO thickness. The deduced parameters from the I–V characteristics suggest that 200 nm is the optimal thickness of the ZnO layer according to our experimental conditions. We attribute the relatively better performance of this thickness to achieving reasonable compensation between serial resistance and ideality factor. The best heterojunction was tested and successfully used as a UV detector.     

On Application of Carbon-Containing Electrode Materials in Technology of Electrospark Alloying: Part 1. Peculiarities of Coating Formation Using Electrospark Treatment of Titanium Alloy OT4-1

Electrospark treatment of OT4-1 titanium alloy was performed sequentially with a STIM-20N hard-alloy electrode (TiC–20% Ni) and carbon-containing material (graphite and carbon-based composite materials). Kinetics of the mass transfer of the hard-alloy electrode was studied. The cathode mass loss during the first minute of the treatment was established. The kinetics results were processed using the methods of mathematical statistics. The erosion resistance of the applied carbon-containing materials was determined. Phase composition and relief of the coatings formed were analyzed. It was found that the application of the carbon-containing material increases the content of refractory phases in the coatings. Increase in the time of the treatment using the carbon-containing materials decreases the roughness of the coatings.     

Medicine Meets Thermal Spray Technology: A Review of Patents

The patent literature concerning thermal spraying for biomedical applications is reviewed in this contribution. The patents were compiled from multiple databases search spanning the 2005-2018 period. For clarity and ease of reading, the results have been grouped into sections according to four individual material groups (apatites, titanium, oxide ceramics, other), with the secondary sorting criterion being related to the specific bioapplication areas (maxillofacial, orthopedic, methods). Lastly, the patents are grouped according to the selected thermal spray method within the individual subsections. In the paper, recent R&D trends in this field are further identified and briefly commented.