Towards intelligent dressing

The aim of this article is to state the principles of an intelligent monitoring and control system for the grinding machine, comprising the dressing process as well as grinding stability.     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Aperture sampling requirements in planar near-field and patterncalculations

The paper covers a simple idea. If we sample an aperture, we can obtain valid patterns over a limited angular region about the normal to the aperture. The same expression can be used with near-field measurements. I reduced the expression to a nomograph. A nomograph allows one to rapidly test various choices. In the second half of the paper, I answer questions caused by the February column which discussed polarization (Milligan, IEEE Antennas. Propag. Mag., vol.38, no.1, p.56-8, 1996)     

The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

A hybrid spreading/despreading function with good SNR performancefor band-limited DS-CDMA

Code-division multiple-access (CDMA) implemented with direct-sequence spread spectrum (DS/SS) signaling is a promising multiplexing technique for cellular telecommunications services. The efficiency of a direct-sequence spread-spectrum code-division multiple-access (DS-CDMA) system depends heavily on the shape of the spectrum of the spread signal. Maximum efficiency is obtained with an ideal brick-wall bandpass spectrum. There are two approaches toward achieving such a spectrum. One is to use a simple spreader that produces a broad spectrum and then follow it with a precise, high order filter to band limit the spectrum. A second approach, which is the approach taken in this paper, is to use a spreader that produces a spectrum close to the ideal spectrum and then employ a simple filter to control the out-of-band power. The proposed spreader/despreader is based on a simple hybrid function and can be easily implemented. An analysis provides a compact expression for the signal-to-noise ratio (SNR) of a RAKE receiver. The expression includes the effects of baseband, intermediate frequency (IF) and RF filtering as well as the effects of the spectral densities of the spreading/despreading functions. The analysis shows that the proposed spreader/despreader yields superior performance over a conventional pseudo noise (PN) spreading/despreading mechanism     

Experimental estimate of self-irradiation of building bricks due to incorporated radionuclides

A method is described for experimentally determining the dose rate created in building bricks by incorporated natural radionuclides. It was established using the thermoluminescence dosimetry method that the measured dose rate depends on the detector thickness, the mass of the ceramic product investigated, and the irradiation geometry. The contributions to the measured dose of weakly penetrating α and β radiation and hard ψ radiation are separated, the ratio between them depending on the experimental conditions. Translated from Izmeritel'naya Tekhnika, No. 7, pp. 62–66, July, 1996.