Efficient usage of highly dispersed Pt on carbon nanotubes for electrode catalysts of polymer electrolyte fuel cells

A Pt-deposited carbon nanotube (CNT) shows higher performance than a commercial Pt-deposited carbon black (CB) with reducing 60% Pt load per electrode area in polymer electrolyte fuel cells (PEFCs) below 500 mA/cm². K₂PtCl₄ and H₂PtCl₆·6(H₂O) are used for the Pt deposition onto multi-walled CNTs (MWCNTs), which are produced by the catalytic decomposition of hydrocarbons. The electric power densities produced using the Pt/CNT electrodes are greater than that of the Pt/CB by a factor of two to four on the basis of the Pt load per power. CNTs are thus found to be a good support of Pt particles for PEFC electrodes. TEM images show 2–4-nm Pt nanoparticles dispersed on the CNT surfaces. These high performances are considered to be due to the efficient formation of the triple-phase boundaries of gas–electrode–electrolyte. The mechanisms of Pt deposition are discussed for these Pt-deposited CNTs.     

Preparation of regioisomers of structured TAG consisting of one mole of CLA and two moles of caprylic acid

TAG (MLM) with medium-chain FA (MCFA) at the 1,3-positions and long-chain FA (LCFA) at the 2-position, and TAG (LMM) with LCFA at the 1(3)-position and MCFA at 2,3(1)-positions are a pair of TAG regioisomers. Large-scale preparation of the two TAG regioisomers was attempted. A commercially available FFA mixture (FFA-CLA) containing 9-cis, 11-trans (9c, 11t)- and 10t,12c-CLA was selected as LCFA, and caprylic acid (C₈FA) was selected as MCFA. The MLM isomer was synthesized by acidolysis of acyglycerols (AG) containing two CLA isomers with C₈FA: A mixture of AG-CLA/C₈ FA (1∶10, mol/mol) and 4 wt% immobilized Rhizomucor miehei lipase was agitated at 30°C for 72 h. The ratio of MLM to total AG was 51.1 wt%. Meanwhile, LMM isomer was synthesized by acidolysis of tricaprylin with FFA-CLA: A mixture of tricaprylin/FFA-CLA (1∶2, mol/mol) and 4 wt% immobilized R. miehei lipase was agitated at 30°C for 24 h. The ratio of LMM to total AG was 51.8 wt%. MLM and LMM were purified from 1,968 and 813 g reaction mixtures by stepwise short-path distillation, respectively. Consequently, MLM was purified to 92.3% with 49.1% recovery, and LMM was purified to 93.2% with 52.3% recovery. Regiospecific analyses of MLM and LMM indicated that the 2-positions of MLM and LMM were 95.1 mol% LCFA and 98.3 mol% C₈ FA, respectively. The results showed that a process comprising lipase reaction and short-path distillation is effective for large-scale preparation of high-purity regiospecific TAG isomers.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

Label-Free in Situ Monitoring of the DNA Hybridization Chain Reaction by Using Sequence-Selective Minor-Groove-Binding Fluorophores

A new label-free in situ monitoring system for the hybridization chain reaction (HCR) based on DNA minor-groove-binding fluorophores [Hoechst 33258 (Hoe) or quinone cyanine-dithiazole (QCy-DT)] has been developed. Use of two unmodified hairpin oligodeoxyribonucleotides containing incomplete double-stranded AATT sequences enabled target-dependent formation of probe binding sites—that is, AATT double strand—in the HCR product, together with fluorescence enhancement of minor-groove-binding fluorophores in situ. This system allows target DNA to be detected through the fluorescence enhancement of Hoe and QCy-DT in real time and in situ. Further development of a label-free, isothermal detection system might provide a cost-effective and user-friendly method for nucleic acid detection.     

Pore pressure development in hybrid fibre-reinforced high strength concrete at elevated temperatures

The present experimental work investigates the build-up of pore pressure at different depths of High Strength Concrete (HSC) and Hybrid-Fibre-Reinforced High Strength Concrete (HFRHSC) when exposed to different heating rates. First, the effect of the measurement technique on maximum pore pressures measured was evaluated. The pressure measurement technique which utilised a sintered metal and silicon oil was found to be the most effective technique for pore pressure measurement. Pore pressure measurements carried out showed that addition of polypropylene fibres is very effective in mitigation of spalling and build-up of pore pressure inside heated HSC. Addition of steel fibres plays some role in pore pressure reduction at relatively higher pressures in deeper regions of concrete during fast heating. Pore pressure development is highly influenced by the rate of heating with fast heating leading to higher pore pressures in the deeper regions of concrete compared to slow heating.     

Analysis of enoyl-coenzyme A hydratase activity and its stereospecificity using high-performance liquid chromatography equipped with chiral separation column

Enoyl-coenzyme A (CoA) hydratase catalyzes the hydration of trans-2-enoyl-CoA to yield 3-hydroxyacyl-CoA during fatty acid degradation (β-oxidation). Although much research has focused on the stereospecificities of 2-enoyl-CoA hydratases, a direct quantification of the production of 3(R)- and 3(S)-hydroxyacyl-CoA has not yet been established. Therefore, we developed a method of concurrently quantifying 3(R)- and 3(S)-hydroxyacyl-CoA using high-performance liquid chromatography (HPLC) equipped with a chiral separation column. The optimized conditions for the separation of 3(R)-, 3(S)-hydroxyhexadecanoyl-CoA and trans-2-hexadecenoyl-CoA, were determined to be as follows: mobile phase of 35/65 (v/v) of 50 mM phosphate buffer (pH 5.0)/methanol; flow rate of 0.5 mL/min; detection at 260 nm; and column temperature of 25°C. This method was applied to subcellular fractions of rat liver; the results directly confirmed that 3(S)-hydroxyhexadecanoyl-CoA is the dominant product obtained from the heat-stable enoyl-CoA hydratase-catalyzed reaction of trans-2-hexadecenoyl-CoA. Finally, the stereospecificities of L-bifunctional protein (L-BP) and D-bifunctional protein (D-BP) were reinvestigated using this method, and it was confirmed that L- and D-BP yielded 3(S)- and 3(R)-hydroxyhexadecanoyl-CoA were yielded from trans-2-hexadecenoyl-CoA, respectively. 3(R)-Hydroxyacyl-CoA is a peroxisomal β-oxidation-specific intermediate. Therefore, this method is potentially useful not only studies regarding the stereochemistry of enoyl-CoA hydratase but also for the diagnosis of diseases caused by defects of peroxisomal enoyl-CoA hydratase.     

Detection of cytochrome P450 substrates by using a small-molecule droplet array on an NADH-immobilized solid surface

Seeing below the surface: A small-molecule droplet array platform on an NADH-immobilized solid surface and a biotinylated acetophenone derivative were developed to identify the substrate candidates for soluble P450 enzymes of interest. This methodology is thought to be easily applicable to other class I P450 systems, including those that use NADPH as cofactor.     

Effects of cubic BN addition and phase transformation on hardness of Al2O3-cubic BN composites

The Vickers hardness of dense Al₂O₃-cubic BN (cBN) composites prepared by spark plasma sintering under a moderate pressure of 100 MPa at 1200-1600 °C was investigated at indentation loads of 0.098-19.6 N. The BN grains in the Al₂O₃-BN composite prepared at 1300 °C showed no transformation from the cBN to hBN phase, and the hardness was 59 GPa at 0.098 N. The hardness of the Al₂O₃ matrix in the Al₂O₃-BN composites containing 10-30 vol% cBN prepared at 1300-1400 °C was around 25 GPa at 0.098 N, which was higher than monolithic Al₂O₃ bodies prepared at the same temperatures. The hardness of the Al₂O₃ matrix in the Al₂O₃-BN composites decreased with increasing sintering temperature. The increase in the hardness of the Al₂O₃ matrix may be due to the decrease in the size of Al₂O₃ grains in the Al₂O₃-BN composites owing to the addition of cBN particles and the decrease in sintering temperature. The Meyer exponents of the monolithic Al₂O₃ bodies and Al₂O₃-BN composites were 1.90-1.94 independent of cBN content.