Alternating copolymer of bithiophene and dialkylbithiazole and its tendency to align on the surfaces

New five-membered ring π-conjugated polymers composed of 2,2′-bithiophene and 4,4′-dialkyl-2,2′-bithiazole units were prepared. The polymers were soluble in 1,2-dichlorobenzene and showed a UV-vis peak at about 490 nm above 120 °C. Cooling the solution led to the appearance of new UV-vis peaks at 550 and 600 nm, which were considered to originate from self-assembled polymer molecules. Powder XRD (X-ray diffraction) data supported a well-stacked solid structure of the polymers and a highly ordered structure of a polymer film formed on a quartz glass substrate. These data revealed a strong tendency of the new polymers to self-assemble and to form an aligned structure on the surface of the substrates.     

Structural characterization of maleic anhydride grafted polyethylene by C NMR spectroscopy

Maleic anhydride grafted polyethylene, [2,3-¹³C₂] MA-g-PE, which was synthesized with ¹³C labeled maleic anhydride [2,3-¹³C₂] MA in solution, was characterized by ¹³C NMR spectroscopy in order to make clear the structure of graft groups. The results reveal that [2,3-¹³C₂] MA-g-PE has succinic anhydride oligomeric grafts with a terminal unsaturated MA ring in addition to well-known saturated succinic anhydride oligomeric grafts and that the former grafts are longer but fewer than the latter.     

Enrichment of arachidonic acid: Selective hydrolysis of a single-cell oil fromMortierella withCandida cylindracea lipase

Three lipases, isolated previously in our laboratory, and a known lipase fromCandida cylindracea were screened for the enrichment of arachidonic acid (AA). The enzyme fromC. cylindracea was the most effective for the production of oil with high concentration of AA. When a single-cell oil fromMortierella alpina, containing 25% AA, was hydrolyzed with this lipase for 16 h at 35°C, the resulting glycerides contained 50% AA at 52% hydrolysis. After this, no further hydrolysis occurred, even with additional lipase. However, when the glycerides were extracted from the hydrolyzate and were hydrolyzed again with new lipase, the resulting oil contained 60% AA, with a recovery of 75% of its initial AA content. Triglycerides were the main components of the resulting oil. The release of each fatty acid from the oil depended on the hydrolysis rate of its ester. The fatty acid, whose ester is the poorest substrate for the enzyme, is concentrated in the glycerides.     

Strictly Conserved Residues in Euphorbia tirucalli β‐Amyrin Cyclase: Trp612 Stabilizes Transient Cation through Cation–π Interaction and CH–π Interaction of Tyr736 with Leu734 Confers Robust Local Protein Architecture

The functions of Trp612, Leu734, and Tyr736 of Euphorbia tirucalli β‐amyrin synthase were examined. The aliphatic variants (Ala, Val, Met) of Trp612 showed almost no activity, but the aromatic variants exhibited high activities: 12.5 % of the wild‐type activity for the W612H variant, 43 % for W612F, and 63 % for W612Y. That is, the enzymatic activities of the variants increased in proportion to the increase in π‐electron density. Thus, the major function of Trp612 is to stabilize transient cations through a cation–π interaction. The Phe and Tyr variants caused a distorted folding conformation, especially at the E‐ring site, which generated the aberrantly cyclized products germanicol and lupeol. The L734G and L734A variants exhibited significantly decreased activities but yielded taraxerol in a high production ratio. The Val, Ile, and Met variants showed markedly high activities (56–78 % of wild‐type activity); therefore, appropriate steric bulk is required at this position. The aliphatic variants of Tyr736 showed markedly decreased activities, but the Phe mutant exhibited high activity (67 %), which indicates that the π electrons are critical for catalysis. Homology modeling indicated that Tyr736 and Leu734 are perpendicular to the substrate and are situated face to face, which suggests that a CH–π interaction occurs between Tyr736 and Leu734, reinforcing the protein architecture, and that Tyr736 cannot stabilize cationic intermediates through a cation–π interaction.     

Evanescent-field scanning microscope with fourier-transform infrared spectrometer

An evanescent-field scanning microscope for infrared microanalysis has been developed. This microscope uses an evanescent field produced by total internal reflection with a high refractive index prism to attain a high spatial resolution, better than the wavelength. This microscope was combined with a Fourier-transform spectrometer. The principle of the method and experimental results for edge detection at different absorption wavelengths are described.     

Terahertz time domain attenuated total reflection spectroscopy with an integrated prism system

We demonstrated attenuated total reflection (ATR) spectroscopy with an integrated prism system that included a terahertz emitter, a terahertz receiver, and an ATR prism. The ATR prism had two internal off-axis parabolic mirrors for, respectively, collimating and focusing the terahertz waves. The Fresnel loss at each interface was reduced, and the total propagation efficiency was 3.36 times larger than when using a non-integrated prism system. The refractive index of water samples calculated from the experimental data showed good agreement with values reported in the literature.     

Experimental and simulation study of undesirable short-period deformation in piezoelectric deformable x-ray mirrors

To construct adaptive x-ray focusing optics whose optical parameters can be varied while performing wavefront correction, ultraprecise piezoelectric deformable mirrors have been developed. We computationally and experimentally investigated undesirable short-period deformation caused by piezoelectric actuators adhered to the substrate during mirror deformation. Based on the results of finite element method analysis, shape measurements, and the observation of x-ray reflection images, a guideline is developed for designing deformable mirrors that do not have short-period deformation errors.     

a study of cast alloys with partially dispersed graphite III: Characterization of high density dispersed surfaces

The characteristic features of cast alloys with partially dispersed graphite are wear resistance and toughness. The friction and wear performance, hardness and other surface characteristics of the cast alloys with a high dispersive density of 60% at the casting surfaces were studied.The reciprocating sliding wear volume of aluminium alloy AC7A containing dispersants decreases with an increase in the gravity variable G = 2π²DN²/60²g, where D (cm) is the diameter of rotation, N (rev min^?1) is the rotational speed and g (cm s^?2) is the acceleration due to gravity, but depends on the nature of the dispersants. The effect of casting temperature on the wear loss was not significant. The dispersive density at the near-surface regions which is susceptible to the magnitude of G has a direct effect on the wear loss. A dense dispersant has an adverse effect on wear resistance and lubricity. A relation between surface roughness and casting temperature is also reported.     

Conditions for growth of AlN single crystals in Al–Sn flux

In this study, we investigated the Al–Sn flux system and its growth conditions to obtain AlN single crystals. AlN single crystals of a size of 50 μm were successfully grown using an Al–Sn melt under nitrogen gas pressure. The growable region of the AlN crystals was established using a pressure‐temperature diagram. The required nitrogen gas pressure for the growth of the AlN crystals was found to decrease with increasing temperature, and AlN was grown at 0.1 MPa nitrogen pressure above 1300°C. By investigating the AlN yield with various Al concentrations, we confirmed that the Al component in the Al–Sn melt facilitated nitrogen dissolution. Finally, scanning electron microscopy analysis showed that the obtained AlN particles showed good morphology.     

An estimation of friction from the indentation of metals by acute-angled conical indenters

The paper describes a method for estimating the coefficient of friction (COF) between sliding surfaces by an indentation of an acute-angled indenter. The COF estimated by the method is compared with the COF measured by a friction tester. The conical indenter, which is made of WC and has an apex angle of 45°, is used for the experiments. A micro-Vickers hardness tester is used for the indentation tests. The friction tester used is one of Bowden–Leben type. A copper and a 0.45% carbon steel are used for the indentation and sliding specimens. The estimation of the COF is based on the equilibrium equation of indentation, which takes the friction between the contacting surfaces of the indenter and the specimen into consideration. The results show that the estimated COF is approximately equal to the measured one. Based on the results, the validity of this method is discussed.