Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

Polymeric phosphonium salts as a novel class of cationic biocides. VII. Synthesis and antibacterial activity of polymeric phosphonium salts and their model compounds containing long alkyl chains

Various polymeric phosphonium salts containing long alkyl chains (C₁₀? C₁₈) and their corresponding model compounds were prepared, which possess the same hydrophobic structure as that of the common disinfectants (quaternary ammonium salts), and their antibacterial activities were evaluated by means of the viable cell counting method against Staphylococcus aureus (Gram-positive) and Escherichia coli (Gram-negative). The polymer with the decyl group exhibited a higher activity than that of the corresponding model compound, particularly against the Gram-positive strain. Furthermore, antibacterial activity of the polymers was found to decrease as the chain length increased. In contrast with the polymers, the antibacterial activity of the corresponding model compounds increased as hydrophobicity of the substituents increased. The antibacterial activity was strongly dependent on the structure, particularly on the length of the alkyl chain. © 1994 John Wiley & Sons, Inc.     

A model for the complex permittivity of water at frequencies below 1 THz

Experimental permittivity data of liquid water, compiled from the open literature, were selectively applied to support a modeling strategy. Frequencies up to 1 THz and atmospheric temperatures are covered with an expression made up by two relaxation (Debye) terms. The double-Debye model reduces to one term when the high frequency limit is set at 100 GHz, and the model can be extended to 30 THz by adding two resonance (Lorentzian) terms. The scheme was carried out by employing nonlinear least-squares fitting routines to data we considered reliable.     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

Quantitative determination of corrosion products and adsorbed water on copper in humid air containing SO2 by IR-RAS measurements

The time dependency of the amounts of corrosion products and co-existing adsorbed water on copper in humid air containing SO₂ was estimated from a series of in situ time-resolved IR-RAS spectra on the basis of the relations between the band intensities and the mass changes of the corrosion products, which were determined by simultaneous measurement of IR-RAS and QCM. The amounts of both corrosion products increased slowly at the initial stage and later increased rapidly. Although the relative humidity was kept constant, the amount of adsorbed water increased nearly the same behavior as that of corrosion products in the stage of relatively small amounts of corrosion products and later increased rapidly when the amounts of corrosion products increased. In humid air without SO₂, sulfite gradually decomposed and some of it changed into sulfate.     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.     

Log-polar height maps for multiple range image registration

We propose a method for coarse registration of multiple range images that uses a log-polar height map (LPHM) as the key for establishing correspondence. The LPHM is a local height map orthogonally mapped on the tangent plane with the log-polar coordinate system. The input range images are roughly represented by signed distance field (SDF) samples. For each SDF sample, an LPHM is generated and is converted to an invariant feature vector. Point correspondence is established by a nearest neighbor search in feature space. The RANSAC algorithm is applied on the corresponding point pairs between each pair of range images, and the pairwise registration of input range images is determined by the extracted inlier point pairs. Finally, the global registration is determined by constructing a view tree, which is the spanning tree that maximizes the total number of inlier point pairs. The result of coarse registration is used as the initial state of the fine registration and modeling. The proposed method was tested on multiple real range image datasets.     

Ergonomics solution for crossing collisions based on field assessment of visual environment at urban intersections in Japan

This paper aims to assess quantitatively the actual visual environment of uncontrolled urban downtown intersections in Japan in relation to frequently occurring crossing collisions and to discuss the safety countermeasures for them. In Field Study 1 dealing with direct visibility, our ultra-wide-angle photograph analysis revealed that most of the right/left-ward visible range at 11 intersections were insufficient to check safety, and the quality of direct visibility was closely associated with causing crossing collisions. The countermeasures to reduce a blind area were determined to be a top priority. In Field Study 2 dealing with indirect visibility, more than half of the 25 traffic convex mirrors had marked shortcomings for preventive safety, and ergonomics guidelines ensuring indirect visibility were proposed for installing traffic convex mirrors. Low-cost/low-technology-oriented countermeasures are highly recommended to obtain clear/sufficient images of crucial information satisfying drivers' requirements on traffic convex mirrors in accordance with those ergonomics guidelines was highly recommended. Crossing collisions could be prevented by improvement of poor direct and indirect visibility.     

Factors associated with serum magnesium and vascular stiffness in maintenance hemodialysis patients

Introduction : We evaluated the associated factors of serum magnesium in patients on maintenance hemodialysis (MHD). Furthermore, we evaluated the relationship between low serum magnesium and arteriosclerosis in these patients. Methods : In 129 patients on MHD, we evaluated the blood levels of magnesium, brachial‐ankle pulse wave velocity (ba‐PWV), ankle‐brachial index (ABI), and intima‐media thickness of the common carotid artery (IMT). Findings : In MHD patients, the serum level of magnesium was significantly correlated with age, calcium, TNF‐α, albumin, and ba‐PWV but not with ABI or IMT. In the multiple regression analysis, albumin (P = 0.0001, β = 0.31) and calcium (P = 0.029, β = 0.18) were selected as significant predictors of the magnesium level in MHD patients. Furthermore, the serum level of magnesium, as well as systolic blood pressure (P = 0.0001, β = 0.32) and age (P = 0.005, β = 0.25), were selected as significant (P = 0.012, β = ?0.22) predictors of ba‐PWV in MHD patients. Discussion : In MHD patients, the serum magnesium level was associated with the serum levels of calcium and albumin. Furthermore, a low serum magnesium level in MHD patients was associated with the index of vascular stiffness.