长庆油田苏平1井固井技术研究与应用

苏平l井完井方式运用了技术套管一次上返、悬挂尾管和筛管技术。该井技术套管段井眼大、裸眼段长，加上大斜度、小间隙的尾管段．对水泥浆体系的性能要求较高。总结分析了长庆天然气水平井苏平l井的固井技术问题，介绍了苏平l井的井身结构与地层性质。通过研究．确定采用低失水GSJ水泥浆体系。该体系成功地应用在三次工程建井过程中，解决了长裸眼、大灰量、大斜度、尾管小间隙等固井技术问题。固井质量达到工程要求。     

催化技术在降低汽油机排放方面的应用

本文介绍了当前催化技术在改善和降低汽油机排放方面的应用情况，指出：催化技术是改善汽油机排放的一种有效措施和重要手段。     

新的载体媒介传递膜

总结了近几年研究和发展的几种载体媒介传递膜。与支撑液膜相比，这些膜具有好的稳定性和长的寿命。对某些物质，如重金属离子、小分子中性碳氢化合物、氨基酸等有高的选择性和通量。它们的传递机理为固定位置跳跃或移动和固定载体2种机理结合。这些研究有望在环境、生物等技术领域中应用。     

云南东川泥石流沟与非泥石流沟~(137)Cs示踪法物源研究

运用1 37Cs示踪法调查云南东川小江流域 6条泥石流沟、6条非泥石流沟和主河的泥沙来源。泥沙主要来源于冲沟侵蚀和滑坡崩塌堆积、坡耕地和草地。坡耕地和草地表层土壤1 37Cs平均含量分别为 0 9Bq m2 和1 98Bq m2 ,冲沟沟壁和滑坡崩塌堆积土体1 37Cs。作者通过 3种源地土体1 37Cs含量的比较 ,分析了细粒泥沙(<0 0 1mm)的来源。 6条泥石流沟冲沟侵蚀和重力侵蚀 (滑坡崩塌 )的相对产沙量变化于 90 2 %～ 1 0 0 % ,平均值为 95 1 % ,6条非泥石流沟的相对产沙量变化于 74 5 %～ 83 3% ,平均值为 78 9%。小江主河为 81 4 %。     

Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.     

基于网络的家电产品故障诊断系统研究

介绍了基于网络的家电产品故障诊断系统的硬件拓扑结构、软件平台及系统开发。系统在硬件上采用了多种网络平台搭建方式及综合连接技术，软件上采用了IDRS诊断模型和基于事例的最新诊断技术。这也是诊断研究和应用的新领域。     

用RAFA方法定量解析芳烃混合物的EEM

本文介绍了降秩因子分析(RAFA)方法,它是从一个多组分混合物中直接定量计算其中某一组分,而不必知道其它组分的物种及含量的一种定量分析的数学方法。它适用于双线性的数据。本实验首先将荧光分光光度计与外接计算机相连,以获得样品的激发-发射矩阵(EEM),再用RAFA方法对蒽、萘、菲、芘、芴、(艹屈)六种标样的一至五组分的混合物进行定量分析,获得满意的结果。     

A fast algorithm for the generalized parametric minimum cut problem and applications

Many combinatorial optimization problems are solved by a sequence of network flow computations on a network whose edge capacities are given as a function of a parameter λ. Recently Galloet al. [7] made a major advance in solving such parametric flow problems. They showed that for an important class of networks, calledmonotone parametric flow networks, a sequence ofO(n) flow computations could be solved in the same worst-case time bound as a single flow. However, these results require one of two special assumptions: either that the λ values are presented in increasing or decreasing order; or that the edge capacity functions are affine functions of λ. In this paper we show how to remove both of these assumptions while obtaining the same running times as in [7]. This observation generalizes and unifies the two major results of [7], and allows its ideas to be applied to many new combinatorial problems. Of greatest importance, it allows the efficient application of binary search and successive binary search to a sequence of network flow problems.     

无间隙原子钢的微观结构特征和塑性应变比

采用Ｘ射线衍射的ＯＤＦ和ＬＰ分析技术，ＳＥＭ电子通道花样和蚀坑技术观测，研究了超深冲无间隙原子钢板的微观结构特征。结果表明：控制化学成分、保证基体纯净、优选工艺参数，促进强的γ－〈１１１〉∥Ｎ．Ｄ纤维织构的形成是获得优异成型性的关键。用ＣＭＴＰ方法，由ＯＤＦ织构数据从理论计算了塑性应变比（ｒ），表明ｒｍ值高达３．１８。文中讨论了再结晶织构形成机制。     

Apolipoprotein(a) concentrations in type 2 (non-insulin dependent) diabetic patients from Romania

Several studies suggested that lipoprotein (a)-Lp(a) is an independent atherogenic risk factor. Since non-insulin-dependent diabetes mellitus (NIDDM) is characterized by an increased risk of coronary heart disease (CHD) as related to the general population, the main purpose of our study was to compare the plasma levels of apolipoprotein (a)-(apo) (a) in 30 NIDDM patients hospitalized in our department, and in 20 non-diabetic controls from Timi?oara. Apo (a) values were similar in the two groups (medians, 95% confidence intervals 57 (50-107) in NIDDM versus 58 (51-106) U/l in controls; p = 0.9097). We found weak correlations between apo (a) and hemoglobin A1 (HbA1) (r = 0.42). A significant association was noticed between apo (a) and apo B, both in NIDDM (r = 0.71) and in control subjects (r = 0.81) p < < 0.001. The diabetic patients were screened for microalbuminaria with the MICRAL-test and we compared apo (a) levels in those having albumin excretion values above and under the cut-off point (20 mg/l). Apo (a) concentrations were similar in both samples. We found no association between apo (a) and plasma lipid values. NIDDM patients on fair glycemic control have similar apo (a) concentrations to non-diabetic subjects and they do not seem to be influenced by diabetes duration, HbA1, microalbuminuria and plasma lipid values Apo (a) and apo B are significantly correlated, both in diabetic and non-diabetic subjects.