非部分嵌套信息结构的LQG动态队决策问题的可解性（II）*

本文讨论非嵌套信息结构的递阶队决策问题和控制均享信息结构的LQG分散控制问题,文中首先证明这两类问题的信息结构都是“部分控制嵌入”的,进而给出最优策略(或控制)存在的充要条件和当此条件成立时最优策略(或控制)的表达式。     

封闭循环TEA CO2激光器用催化剂的实验研究

在不同的催化剂和不同温度的条件下,用磁氧分析仪监测了封离型TEA C0₂激光器中O₂含量随时间或脉冲次数的变化。对实验现象进行了分析。对几种催化剂的特性给出了详细的比较。     

黄冈市农村卫生人才培养的现状与对策

本文采取问卷调查和文献查阅相结合的方式,对黄冈市卫生专业技术人员队伍现状进行了调查和分析,剖析了黄冈市农村卫生人才培养的方法和经验,提出了切实可行的农村卫生人才培养的对策与建议。     

基于遗传算法的平流层飞艇路径规划设计

利用传统线性化方法--小扰动法将模型线性化,结合平流层飞艇的工作特性,把飞艇上升运动看成是纵向基准运动和横侧向扰动运动.然后采用最小值原理,根据飞艇的控制量和边界条件,设计和优化飞艇的上升轨迹,其性能目标函数是从初始点到目标点运动过程中能量消耗最小.利用遗传算法,在运动模型和控制量变化的共同约束作用下,求取目标函数的最小值.最后根据飞艇实际工作过程,对仿真结果分析表明,该方法具有实际应用价值.     

关于Photoshop插件的SAR图像处理探究

SAR图像处理主要包括相干斑抑制、特征提取等,如果在使用Photoshop插件SAR图像处理图片,将主要精力集中于算法的设计和优化方面,可以尽量减少在用户界面、内存管理和基本的图像操作方面的编程,既可以实现多种图像处理,又容易实现功能的充分扩大与填充,从而在最短的时间内做做多的事。     

Effect of nitrogen and nickel on the stability of an Fe-12Cr-23Mn austenitic steel

The effect of nitrogen and nickel on the austenite stability and the structural changes as a result of cold work of an Fe-12Cr-23Mn alloy steel has been examined by transmission electron microscopy and X-ray analysis. Prestrain was performed either at room temperature or at 200° C. Final strain was carried out at liquid nitrogen temperature. The volume fraction of strain-induced martensite decreased by 40% and 12% due to the addition of 2.43% Ni and 0.11% N, respectively, despite whether prestrain was performed or not. The mechanisms are discussed in terms of the phase, stacking faults, dislocation cells and dislocation tangles induced by prestrain and final strain.     

Stability and work hardening of an Fe-12Cr-23Mn austenitic steel

The effect of pre-strain on the strain-induced martensitic transformation of an Fe-12Cr-23Mn austenitic steel has been investigated through transmission electron microscopy and X-ray analysis. Pre-strain was performed either at room temperature or at 200° C. Final strain was carried out at liquid-nitrogen temperature. The phase was shown to form on {1 1 1} planes of the austenite matrix predominantly by overlapping of stacking faults. The martensite transformation sequence was . Nucleation of the phase mainly occurred at intersections of bands. Austenite stability was shown to increase by pre-strain at 25° C or 200° C. Pre-strain at 200° C has a greater effect on austenite stability than does pre-strain at 25° C. The mechanism was discussed in terms of martensite transformation rate and various substructures introduced during straining. Work hardening was shown to depend on the degree of pre-strain and final strain. The correlation between work hardening and substructures introduced during straining was examined.     

粉煤灰填充尼龙6浇铸制品的研究

将粉煤灰用硅烷偶联剂处理后填充到尼龙6浇铸制品(MC尼龙)中,可以改善制品的吸水性、收缩率及热稳定性等,还可以降低成本。该项研究结果有很大的实用价值。     

Simulation of the tubular positive electrode of the lead-acid battery

The discharge performance of a tubular electrode of the lead-acid battery based on a pseudo steadystate approach was simulated. It was found that the discharge reaction started from the central interior region instead of from the outer surface as in the usual plate-type electrodes. This is due to the fact that the central region has a smaller reaction surface than the outer region of the tubular electrode. This consequently causes a higher current density near the center. A comparison of the theoretical prediction and experimental result shows that the model is fairly accurate except for very high rate discharge conditions.     

Calendering of non-newtonian fluids

The calendering of non-Newtonian fluids by two rotating cylinders to produce thin films of fluids finds wide application in polymer sheet-making and food-drying industries. Theoretical work has previouly been devoted to the symmetrical case where the cylinders are of equal diameters rotating at the same speed. The present work proposes a new one-film theory of calendering of power law fluids for unequal radii and surface velocities of the calendering cylinders. The relationship between the dimensionless thickness of the calendered fluid, Δ_e^* and that of the incoming fluid, Δ_i^* is shown to be a function of the ratio of the surface velocities of the cylinders and the power law index. The result further shows that Δ_e^* tends to asymptote after the second decade of Δ_i^*