Behavior of residual carbon in Sm(Co, Fe, Cu, Zr)z permanent magnets

When sintered Sm(Co, Fe, Cu, Zr)_z permanent magnets are prepared by metal injection molding, some organic binders are added in alloy powder, which leads to much residual carbon in the magnets. The residual carbon decreases magnetic properties and destroys the microstructure of the magnets. In this paper, the behavior of carbon in Sm(Co, Fe, Cu, Zr)_z permanent magnets has been studied. The results indicate that Sm(Co, Fe, Cu, Zr)_z magnets can keep excellent magnetic properties when the carbon content is below 0.1 wt.%: Br ≥ 10 kGs, H_cj ≥ 22 kOe, BH_max ≥ 25 MGOe. When the carbon content is above 0.1 wt.%, Br, H_cj and BH_max decrease with increasing carbon content evidently. Carbon consumes Zr content and forms ZrC, which reduces the volume fraction of the lamella and Sm(Co, Cu)₅ phases. Thus, the cell size increases and the cellular microstructure deteriorates. When the carbon content reaches 0.43 wt.%, there is not enough Sm(Co, Cu)₅ phase to form a uniform cellular microstructure. Br, H_cj and BH_max are approximate to zero. Since carbon has little influence on the content of Sm₂(Co, Fe)₁₇ phase, Ms can keep a high value (≥100 emu/g). ZrC has high melting point (3420 °C) and acts as dispersion particle in the magnets, which prevents the grains of SEM structure growing and reduces the liquid content of green compacts during sintering. Therefore, the density of the magnets decreases.     

Determination of Active Slip/Twinning Modes in AZ31 Mg Alloy Near Room Temperature

In order to determine the deformation modes in AZ31 magnesium alloy at room temperature, computer simulations of deformation texture development and calculation of formability have been carried out. The simulation results were compared with the measured texture results. Based on agreement between the experiments and simulations the active deformation modes were determined. A Visco Plastic Self Consistent model was employed for the simulation of plastic deformation. Simulations and experiments were performed for different initial textures. The goal of the study was to develop the understanding of deformation texture evolution and its effects on mechanical properties of magnesium, with an ultimate goal of improving room temperature formability of magnesium alloys. This article was presented at Materials Science & Technology 2006, Innovations in Metal Forming symposium held in Cincinnati, OH, October 15-19, 2006.     

Effects of solid solution alloying on creep deformation of aluminum

The effects of solid solution alloying on the creep-rupture properties, deformation characteristics, ductility, and fracture of pure aluminum were studied by means of creep-rupture tests on polished specimens of three alloys each of Al-Cu (0.24, 0.79, and 2.05 pct Cu), Al-Zn (4.93, 9.89, and 19.78 pct Zn), and Al-Mg (0.94, 1.92, and 5.10 pct Mg) at 500°, 700°, and 900°F.     

Microstructure and creep behavior in AE42 magnesium die-casting alloy

The micro structural analysis of die-cast AE42 reveals a correlation between micro structure and creep strength. A lamellar-phase Al₁₁RE₃, which dominates the interdendritic microstructure of the alloy, partly decomposes above 150‡C into Al₂RE and Al (forming Mg₁₇Al₁₂). The increased solubility of aluminum in magnesium at higher temperatures may also promote the decomposition of Al₁₁RE₃. The creep strength decreases sharply with these phase changes. A mechanism for the decrease in creep strength of AE42 is proposed whereby the reduced presence of lamellar Al1₁₁RE₃ and/or the presence of Mg₁₇Al₁₂ contribute to the observed poor creep strength at higher temperatures.     

显微组织对Ti-6Al-4V ELI合金疲劳裂纹扩展速率的影响

研究了Ti-6Al-4V ELI合金板材的显微组织对疲劳裂纹扩展速率的影响。用金相显微镜对不同热处理制度下该合金α和β转变组织的变化进行了观察分析。采用MTS-810低周疲劳试验机测试合金的裂纹扩展速率。通过Origin 6.0软件对数据进行处理并绘制裂纹扩展速率（△a／△N）与应力强度因子幅△K的关系曲线。结果表明：在Pairs区范围内，疲劳裂纹扩展速率对双态组织中初生α相含量的多少不敏感，而在近门槛区和快速扩展区，裂纹扩展速率对组织比较敏感；在本实验研究的条件下，细针编织状魏氏组织的da／dN〈平直状片层组织的da／dN〈双态组织的da／dN。     

Chromium distribution between liquid iron and molten basic slags

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-SiO₂-FeO-Cr₂O₃ type in the temperature range 1526° to 1734°C The effects of slag oxidation, temperature, and basicity were observed.     

The preparation of tantalum powder using a MR-EMR combination process

In the conventional metallothermic reduction (MR) process used to obtain tantalum powder in batch-type operation, it is difficult to control the morphology and location of the tantalum deposits. In contrast, an electronically mediated reaction (EMR) process is capable of overcoming this difficulty. It has the advantage of being a continuous process, but has the disadvantage of a poor reduction yield. A process known as the MR-EMR combination process is able to overcome the shortcomings of the MR and EMR processes. In this study, an MR-EMR combination process is applied to the production of tantalum powder via sodium reduction of K₂TaF₇. In the MR-EMR combination process, the total charge passed through an external circuit and the average particle size (FSSS) increase as the reduction temperature increases. In addition, the proportion of fine particles (−325 mesh) decreases as the reduction temperature increasess. The tantalum yield improved from 65 to 74% as the reduction temperature increased. Taking into account the charge, impurities, morphology, particle size and yield, a reduction temperature of 1123 K was found to be optimum for the MR-EMR combination process.     

Erosion testing and surface preparation using abrasive water-jetting

Erosion testing and surface preparation are studied using a 3-axis Computer Numerical Control (CNC) abrasive water jetting (AWJ) apparatus. The effects of erosion time t, impingement angle α and pressure p on the erosion rate E, average surface roughness R _a, and surface hardness Rockwell C Hardness (HRC) were investigated in detail. Compared with conventional grit blasting, AWJ can reduce grit embedment in the target material due to the action of the high-pressure water. AWJ also has the advantage of generating a higher average surface roughness R _a over water jetting (WJ) due to the action of abrasive particles. In addition, AWJ increases the surface hardness HRC of the substrate material. The obtained higher degree of average surface roughness is helpful for improving the bonding strength between the coating and the substrate material. The erosion testing and the surface preparation are numerically controlled by a 3-axis CNC system; therefore precise and detailed results for various operating parameters can be obtained.     

基于等效电路分析的航空锂电池工作特性研究

针对航空锂电池安全保障问题,提出了一种基于等效电路模型的锂电池工作特性分析方法。该方法通过PNGV等效电路处理,实现对航空锂电池物理反应过程的电路模拟,并基于此研究了航空锂电池的工作特性。实验结果表明,该方法能够实现对航空用75 Ah锂电池等效电路的有效模拟,等效模型能够有效分析不同条件下的电池工作状态,获得锂电池工作特性规律,为锂电池的安全航空应用提供保障。