Co-digestion of ruminal content and blood from slaughterhouse industries: influence of solid concentration and ammonium generation.

At the present time, organic solid wastes from industries and agricultural activities are considered to be promising substrates for biogas production via anaerobic digestion. Moreover solids stabilisation is required before reutilization or disposal. Slaughterhouses are among the most important industries in Uruguay and produce 150,000 tons of ruminal content (RC) and 30,000 tons of blood per year. In order to determine the influence of the solids and blood contents, the ammonia inhibition and the inoculum adaptation co-digestion batch tests were performed. A set of experiences with TS concentration of 2.5%, 5% and 7.5% and different ratios of RC/blood were carried out using an inoculum from an UASB reactor. In all experiences fast blood hydrolisation was observed. A higher methane production was detected in the experiences with higher TS content. However, the fraction of solids degradation was lower in these experiences. A plateau in the biogas production was found. The free ammonia level, which was above the reported inhibitory levels, could explain this behaviour. After the inhibition period the biogas production restarted probably due to the biomass acclimatisation to the ammonia. In order to determine the inoculum adaptation a new experiment was performed. The inoculum used was the sludge coming from the first set of experiences. Based upon batch tests a 3.5 m3 pilot reactor was designed and started up. Ammonia inhibition was avoided by the start-up strategy and in two weeks the biogas production was 3.5 m3/d. The VS stabilisation with a solid retention time of 20 days was of 43%. The pilot reactor working at steady state had a TS concentration of 3-4% with a ratio of RC/blood of 10:1 at the entrance.     

Beneficial effects of wettability altering surfactants in oil-wet fractured reservoirs

In fractured reservoirs, an effective matrix-fracture mass transfer is required for oil recovery. Surfactants have long been considered for oil recovery enhancement, mainly in terms of their ability to reduce oil–water interfacial tension. These surfactants are effective when the fractured formations are water-wet, where capillary imbibition of surfactants from the fracture into the matrix contributes to oil recovery. However, another beneficial aspect of surfactants, namely their ability to alter wettability, remains to be explored and exploited. Surfactants capable of altering wettability can be especially beneficial in oil-wet fractured formations, where the surfactant in the fracture diffuses into the matrix and alters the wettability, enabling imbibition of even more surfactant into the matrix. This sequential process of initial diffusion followed by imbibition continues well into the matrix yielding significant enhancements in oil recovery.In order to test this hypothesis of sequential diffusion–imbibition phenomenon, Dual-Drop Dual-Crystal (DDDC) contact angle experiments have been conducted using fractured Yates dolomite reservoir fluids, two types of surfactants (nonionic and anionic) and dolomite rock substrates. A new experimental procedure was developed in which crude oil equilibrated with reservoir brine has been exposed to surfactant to simulate the matrix-fracture interactions in fractured reservoirs. This procedure enables the measurements of dynamic contact angles and oil–water interfacial tensions, in addition to providing the visual observations of the dynamic behavior of crude oil trapped in the rock matrix as it encounters the diffusing surfactant from the fractures. Both the measurements and visual observations indicate wettability alterations of the matrix surface from oil-wet to less oil-wet or intermediate wet by the surfactants. Thus this study is of practical importance to oil-wet fractured formations where surfactant-induced wettability alterations can result in significant oil recovery enhancements. In addition, this study has also identified the need to include contact angle term in the dimensionless Bond number formulations for better quantitative interpretation of rock–fluids interactions.     

Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys: Part I. Tensile deformation

The effects of α and β phase interactions on the room-temperature tensile and creep deformation behavior of α + β titanium alloys with Widmanst?tten microstructures were studied using Ti-6.0 wt pct Mn and Ti-8.1 wt pct V as the model two-phase alloy systems. This article, Part I, deals with tensile deformation. It was found that when the α phase is present as thin (<10-μm) plates in the α + β alloys, significant twinning occurs. No significant twinning was observed in single-phase alloys with the same chemistry and similar grain size. Additionally, the β phase of Ti-8.1 V deforms by stress-induced hexagonal martensite (α′), while only twinning occurs in the single-phase β alloy with the same chemistry. Twinning in the α phase in association with stress-induced martensite (SIM) in the β phase was observed for the first time in a two-phase titanium alloy. This behavior is explained in terms of a number of factors including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability.     

Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Design of a retention tank: comparison of stormwater quality models with various levels of complexity.

Stormwater quality simulation models are useful tools for the design and management of sewer systems. Modelling results are highly sensitive to experimental data used for calibration. This sensitivity is examined for three modelling approaches of various complexities (site mean concentration approach, event mean concentration approach and build-up, washoff and transport modelling approach) applied to a typical case study (design of a dry detention tank), accounting for the variability of calibration data and their effect on simulation results. Calibrated models with different calibration data sets were used to simulate 3 years of rainfall with different retention tank specific volumes. Annual pollutant load interception efficiencies were determined. Simulations results revealed (i) that there is no advantage in using the EMC model compared to the SMC model and (ii) that the BWT model resulted in higher design ratios than those given by the SMC/hydraulic approach. For both EMC and BWT models, using an increasing number n of events for calibration leads to narrower confidence intervals for the design ratios. It is crucial for design ratios to account for successive storm events in chronological order and to account for the maximum allowable flow to be transferred to the downstream WWTP.     

Development of a simple microsystems membrane probe card

Presented here are details of the development of a novel membrane integrated circuit (IC) probe card structure based on microsystems technology. The device design allows probing of both solder bumps and pads. A self-limiting sensor was integrated to prolong device lifetime. Comparison with and discussion of the use of modelling is made. Possible enhancements to the probing structure are discussed to improve alignment and measurements. Also shown is data using our microsystems probe card to access a simple IC device. Our device has a contact resistance of less than 0.5 Ω for a force of 0.004 N. A method to implement our probing structure for commercial application and the potential developments which can be made to improve its ease of use are then discussed.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Improved homogenization of Ni in sintered steels through the use of Cr-containing prealloyed powders

The homogenization of Ni in powder metal (PM) steel compacts is usually difficult even after high-temperature sintering at 1250°C. An earlier study by the authors demonstrated that this problem can be alleviated through the addition of 0.5 wt pct Cr in the form of stainless steel powders. To further improve the microstructure and mechanical properties of Ni-containing PM steels and to understand the mechanisms, an attempt was made in this study using the Fe-3Cr-0.5Mo prealloyed powder as the base material. The results showed that the distribution of the Ni additives was significantly improved. As a result, the tensile strength of the Fe-3Cr-0.5Mo-4Ni-0.5C compact sintered at 1250°C reached 1323 MPa. The elongation was higher than 1 pct. These sinter-hardened properties, which were attained using a slow furnace cooling rate, were comparable to those of the sinter-hardened alloys reported in the literature using accelerated cooling and were equivalent to those of the best quenched-and-tempered alloys registered in the Metal Powder Industries Federation (MPIF) standards. These improvements were attributed to the positive effect of Cr addition on alloy homogenization due to the reduction of the repelling effect between Ni and C, as was demonstrated through the thermodynamic analysis using the Thermo-Calc program.     

Note on B-splines, wavelet scaling functions, and Gabor frames

Let g be a continuous, compactly supported function on such that the integer translates of g constitute a partition of unity. We show that the Gabor system (g,a,b), with window g and time-shift and frequency-shift parameters a,b>0 has no lower frame bound larger than 0 if b=2,3,... and a>0. In particular, (g,a,b) is not a Gabor frame if g is a continuous, compactly supported wavelet scaling function and if b=2,3,... and a>0. We give an example for our result for the case that g=B/sub 1/, the triangle function supported by [-1,1], by showing pictures of the canonical dual corresponding to (g,a,b) where ab=1/4 and b crosses the lines N=2,3,.