CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Stability analysis of regional and national voting schemes by a continuous model

The previous discrete-model-based stability analysis of regional and national voting has been extended to a continuous-model-based analysis in the simultaneous presence of white and concentrated components of noise, reconfirming the previous conclusion that regional voting with smaller sized regions always demonstrates an improved stability over those with larger sized regions, including the national voting in its limiting case in particular. The conclusion remains valid as long as the weak distribution assumption is valid.     

Stability of Mixtoxantrone Hydrochloride in Solution

A stability-indicating reversed-phase high performance liquid chromatographic method was developed for the detection of mitoxantrone HC1 and its degradation products under accelerated degradation conditions. The degradation kinetics of mitoxantrone HC1 in aqueous solution over a pH range of 1.18 to 7.20 and its stability in propylene glycol-or polyethylene glycol 400-based solutions were investigated. The observed rate constants were shown to follow apparent first-order kinetics in all cases. The pH-rate profile shows that maximum stability of mitoxantrone HC1 was obtained at pH 4.01. No general acid or base catalysis from acetate or phosphate buffer species was observed. The catalysis rate constants on the protonated mitoxantrone imposed by hydrogen ion water and hydroxy ion were determined to be 3.72 × 10 min^-1 5.64 × 10-min^-1 and 1.108 × 10^-2min^-1, respectively. The degradation rate constants of mitoxantrone affected by different ionic strength systems. Irradiation with 254 nm UV light at 25±0.5°C was found when canpared with the light-protected controls. Incorporation of nonaqueous propylene glycol or polyethylene glycol in the pH 4.01 mitoxantrone solution shows an increase in its stability at 502±0.5°C.     

Evaluation of Soybean Seedcoat Cracking During Drying:PART II. Using MRI

MRI techniques were developed and employed for non-destructive and noninvasive study of seedcoat cracking in low moisture soybean kernels during heated air drying. Proton density image and transient moisture distribution profile of a single soybean kernel can be obtained using MRI. These MRI techniques proved to be particularly useful for the continuous observation of initiation and propagation of seedcoat cracking during the entire period of drying process without interruption.

The proton density images of soybean kernels showed that seedcoat cracking was initiated perpendicular to the long axis of the kernel near the hilum. The transient moisture distribution profiles in soybean kernels during drying indicate that moisture gradient developed during drying was higher in the seedcoat than in the cotyledon. Drying temperature and initial average moisture content were positively correlated with the soyhean seedcoat crackig. The location of the     

Characterization of proton-exchanged optical waveguides in ZnO:LiNbO3

We report the first demonstration of proton-exchanged optical planar waveguides in x-cut and z-cut LiNbO₃ doped with 6 mol% ZnO using adipic acid as proton source. These waveguides exhibit a graded index profile which can be modeled by a linear step function with a surface index increase of 0.135 and 0.14 for x-cut and z-cut waveguides, respectively. The diffusion constant D_o and the activation energy Q are characterized optically to be 1.64×10⁹ μm²/h and 88.8 KJ/mol for x-cut waveguides, and 1.478×10⁹ μm²/h and 91.25 KJ/mol for z-cut waveguides, respectively. The diffusion rate along the z-axis is slower than that along the x-axis, whereas the surface index increase on z-cut waveguides is larger than that on x-cut waveguides.