铝质材料的摩擦学表面改性

铝质材料阳极氧化膜系均匀、规则的微观多孔质结构，利用物理、化学或电化学的方法在其中沉积或原位合成润滑性物质，在保持阳极氧化膜质硬、耐磨特性的基础上，使其具有一定的白润滑性，是近十多年来铝质材料表面改性研究的热点领域之一，本文对该研究的基本原理和国内外发展概况进行了概述，并重点介绍了我们在这一方面研究中的一些最新进展和结果，分别介绍了三种新型体系的自润滑改性阳极氧化铝材料．     

Reaction process of monazite and bastnaesite mixed rare earth minerals calcined by CaO-NaCl-CaCl2

The decomposition reactions of monazite and bastnaesite mixed rare earth minerals calcined by CaO-NaCl-CaCl2 were studied by means of TG-DTA and XRD. The results show that the process of the minerals decomposed by CaO involves two steps. The first step occurs in the temperature range of 425-540 ℃, and the main reactions are bastnaesite decomposition, i.e. REOF reacts with CaO to produce RE2O3 and CaF2, and Ce2O3 is oxidized to CeO2. During this step, CaCO3 is formed at about 500 ℃. The second step takes place in the temperature range of 610-700 ℃, and the reactions are monazite decomposition into RE2O3, Ca5F（PO4）3 and Ca3（PO4）2 by CaO and CaF2. In this process, the decomposition ability is improved because CaO from CaCO3 decomposing has high chemical activity. In calcining process, the new formed Ca5F（PO4）3 restrains fluorine that can escape in form of gaseous compound. The decomposition ratio of the mixed rare earth minerals reaches 90.8% at 700 ℃.     

Sn-Cu系无铅钎料的研究现状与发展

介绍了无铅钎料应用时应该满足的基本要求和Sn-Cu系无铅钎料的国内外研究和应用现状,概述了Sn-Cu系无铅钎料润湿性能、物理性能、力学性能等方面的一些特点,分析探讨了Sn-Cu系无铅钎料存在的不足,详细阐述了添加不同合金元素(如Bi、Ag、Ni、RE等元素)对Sn-Cu系无铅钎料性能的影响规律,并对Sn-Cu系无铅钎料的应用前景和发展方向进行了展望.     

化学冶金因素对埋弧焊焊缝硫磷含量的影响

通过试验和理论分析，探讨了在埋弧焊过程中，熔池中Ｓ，Ｐ的脱去过程，主要是以分别生成硫酸盐和磷酸盐的形式进行的化学冶金反应，并提出了熔池中的硫，磷脱去过程存在一个极限值，而这个极限值与焊剂的碱度和焊剂，焊丝及母材中的硫，磷含量有关。在焊剂碱度ＢＩ≥２．５的高碱度焊剂中，根据焊丝或焊剂中硫含量的不同，熔敷金属中硫的的极限值可低于焊丝中的硫含量或接近焊剂中的硫含量；而磷的极限值为０．０１０％±０．００２     

稀土掺杂锆钛锡酸铅镧（PLZST）的化学合成研究

通过化学共沉淀法合成PLZST多晶料，采用XRD和SEM对多晶料进行表征，考察了煅烧温度、过量Pb掺量、退火处理等条件对PLZST多晶料的影响。研究结果表明，化学共沉淀法合成PLZST具有一定的适用范围，在低温750℃下保温2h便能得到单一的钙钛矿相，掺入过量的Pb有利于PLZST晶体的生成，适当的退火处理能促进晶体长大。     

Ce对过共晶Al—Si合金熔体粘滞性和结构的影响

研究了Ce对Al—16％Si合金熔体粘滞性的影响。结果表明：Ce的加入增加了合金熔体的粘度，且随着Ce含量的增加粘度值也增加。结合加入Ce的Al—16％Si合金氢含量的变化、凝固组织和DSC曲线研究了熔体结构的变化，分析了粘度与液态结构变化之间的关系。     

辐照损伤对锆合金电化学性能的影响

综述了堆内辐照对锆合金电化学性能影响的概况，浅析了堆内辐照损伤的机理，并重点探讨了主要的堆内辐照源——中子辐照对锆合金微观结构与氧化性能的影响。进一步阐述了堆外离子轰击模拟堆内中子辐照研究方法的进展概况，并就离子轰击实验参量的选择进行了较为深入的分析。     

石墨化率不同的自焙炭块的热膨胀

采用精密垂直拉杆膨胀仪在１４～１０００℃范围内测量了具有不同石墨化率的自焙炭块的相对热伸长量，并由此获得了热线膨胀系数α。结果表明：石墨化率一定时，α值在较低温度下随温度升高而增加，在较高温度下，α值随温度变化不明显；恒温时，石墨化率越高，α值越低。讨论了单位热应力下的弹性模量概念     

Effects of CeF3 on properties of self-shielded flux cored wire

0 IntroductionSelf-shielded flux cored wire is a newly developedwelding material used without gas protection. Use of suchcored wires has grown rapidly in developed countriesbecause of the following advantages: simple use, goodwind resistance ability, lower cost resulted from highproductivity and strong desulfurization ability[1]. Self-shielded flux cored wires are preferred for on-site weldingsuch as ship and barge building, storage tank, bridge,offshore oil platform buildings and so on[2 -3].…     

Investigation on gradient material fabrication with electron beam melting based on scanning track control

A new electron beam control system was developed in a general vacuum electron beam machine by assembling with industrial control computer, programmable logic control （PLC）, deflection coil, data acquisition card, power amplifier, etc. In this control system, scanning track and energy distribution of electron beam could be edited off-line, real-time adjusted and controlled on-line. Ti-Mo gradient material （GM） with high temperature resistant was fabricated using the technology of electron beam melting. The melting processes include three steps, such as preheating, melting, and homogenizing. The results show that the GM prepared by melting technology has fine appearance, and it has good integrated interface with the Ti alloy. Mo and Ti elements are gradually distributed in the inter.face of the gradient material. The microstructure close to the Ti alloy base metal is α ＋ β basket-waver grain, and the microstructure close to the GM is a single phase of β solid solution.