激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

一种支持QoS的拓扑自适应动态组播路由算法

YAM、QoSMIC、DSDMR等一类支持QoS的动态组播路由算法允许组播成员动态地加入和离开，同时为接收方提供多个可选择的组播接入路径，以满足不同应用的QoS需求。但这些算法普遍存在控制信令开销大和结点加入时延长，可扩展性不好等问题。本文在分析这些算法的基础上，提出改进的支持QoS的动态组播路由算法，即拓扑自适应动态组播路由（Topology Adaptive Dynamic Multicast Routing，TADMR）算法。该算法避免了以往算法中大部分盲目的路径搜索，并使结点加入时延不再受限于固定的等待时钟，而与网络拓扑相自适应。性能分析和仿真结果表明，该算法具有较低的控制信令开销和结点加入时延，适用于各种网络规模和群组规模，具有良好的可扩展性。     

WLAN网管系统的现状和发展

2001年以来，全球WLAN（无线局域网）市场应用的瓶颈被打破，中国也迎来了WLAN商业化运作和服务的春天，WLAN为我们带来了一种全新的、灵活的工作方式，同时也带来了新的挑战，本文将对WLAN网络管理的主要内容和具体指标进行阐述，并对各大厂商的WLAN网管产品进行简单介绍和比较。     

双时基频率校准电路

提供精确的时间基准是精密仪器和高精度设备计时和工作的关键技术之一。文中采用两套晶振电路，通过分频产生高频和低频两个频率信号，采用编码的方法对两个频率信号在每一个时钟周期内进行动态校核，只有两个晶振的频率在允许的精度范围内，或同时增大（缩小）相同的倍数，校核后频率信号才是正确的，且能给系统提供精确的时间基准。该方法能有效防止系统的时钟周期因意外的原因伸长或缩短。整个电路可以作为精密仪器或高精度设备的一个模块电路。     

地源热泵——辐射地板联供试验

通过地源热泵－辐射地板系统冬夏联供试验，讨论了该系统作为新型环保节能空调方式的可行性及优越性，并对运行中出现的问题进行分析。     

钨合金废料的资源再生利用技术

钨是一种稀有金属，钨合金具有高的强度、硬度，较好的耐高温性、耐密性和良好的电性能。广泛应用于航空航天工业、兵器工业、核工业、信息产业、汽车工业和钢铁工业等行业。目前，钨资源短缺，钨合金价格高、用量大，因此各国都把废弃的钨合金作为宝贵的第二钨资源加以再生利用。本文综述了钨合金的再生利用现状，分别总结了硬质合金、高比重合金、钨铜合金和钨材的再生利用技术，并利用生态环境材料的观点。对每种再生利用技术作了简单的评价。     

Cholesterol‐imprinted polymer receptor prepared by a hybrid imprinting method

A novel cholesterol‐imprinted polymer (CMIP‐H) was prepared by a hybrid method of covalent imprinting and non‐covalent imprinting. This approach involves the copolymerization of a template‐containing monomer, cholesteryl 2‐hydroxyethyl methacrylate carbonate, and a cross‐linker, followed by hydrolysis to afford a flexible guest‐binding site accompanied with the easy and efficient removal of a ‘sacrificial spacer’. The effect of solvent on the binding capacity of CMIP‐H towards cholesterol was studied, indicating that a good binding capacity towards cholesterol could be achieved in a less‐polar solvent. The binding experiments of CMIP‐H towards a series of structural analogues of cholesterol, including cholesterol acetate, progesterone and stigmasterol, were carried out in hexane. The results showed that CMIP‐H almost did not bind cholesterol acetate at all because the hydrogen‐bonding site is blocked. It exhibited a similar binding towards both cholesterol and stigmasterol, but much higher binding towards progesterone. Copyright © 2005 Society of Chemical Industry     

Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

Preparation of BaMgAl10O17∶Eu2+ and Its Phase Behavior in Microemulsion System

BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra.