24万t/a尿素装置技术改造总结

针对新化化肥有限公司尿素装置存在的问题进行了技术改造,从尿素合成塔、中压分解吸收、低压分解吸收、闪蒸等方面分析了产生问题的原因,提出了改进措施和实施方案。对改造前后工艺指标、产品质量和经济效益进行了对比和分析。改造结果表明.生产能力提高25％,5个月可收回全部投资。     

深井长裸眼跨隔测试新工艺的应用

为减少勘探费用，缩短施工周期，取全取准各项地质资料，采取中途测试工艺。随着深井中途测试不断增多，特别是跨隔支撑测试具有一定施工风险和难度，要求测试质量不断提高。结合油田生产实际，合理选配了地层测试工具仪表，不断改进测试管串和优化施工设计，经盐22井中途跨隔测试应用，获得成功。     

基于子波域空间相关的多分辨图像滤波方法

从静态子波变换入手,提出了一种有效的图像滤波算法。通过计算相邻尺度下细节信号的空间相关性来区分噪声和信号,如果子波系数的空间相关性大,则认为此位置的系数含有特征及边缘信息予以保留。实现这种理论的完整方法包括两部分:空间滤波和子波收缩。仿真结果表明这个算法有很好的降噪性能。     

主动雷达终端实时仿真软件的设计与实现

在主动雷达数据回放显示的基础上,通过使用D irectDraw和Intel IPP技术,设计了主动雷达终端实时仿真软件,包括信号处理、数据处理及终端显示等模块,极大地提高了软件的执行效率,使得整个仿真过程具有良好的实时性。本文介绍了该软件的设计及实现。     

松辽盆地南部深层火山岩识别及成藏条件分析

松辽盆地北部徐深1井在营城组火山岩获得油气突破后，在松辽盆地南部长岭断陷针对火山岩部署了长深1井。在长深1井营城组火山岩地层测试获4.6×105m3/d的工业气流，推算无阻流量1.5×106m3/d以上，预示松辽盆地南部深层火山岩气藏是下步勘探开发的主要领域。通过大量的火山岩岩心资料，利用岩石学、矿物学、测井和地震地层学等多学科技术，首次在松辽盆地南部建立了火山岩识别标准，在东南隆起区部署探井1口，在火山岩中见到了较好的气显示，取得很好的效果。     

金属泡沫材料研究进展

综述了金属泡沫材料的各种制备方法。液相法制备金属泡沫材料包括气体吹入法、固体发泡剂法和固体—气体共晶凝固法、熔模铸造法、渗流铸造法、喷射沉积法以及粉末加压熔化法等制备方法。采用金属粉末烧结法、浆料发泡法等制备工艺可以从固相制备金属泡沫材料。电沉积法以及气相沉积法可用于制备高孔隙率的金属泡沫材料。最后简要总结了金属泡沫材料的应用。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.