公司大门工程建设施工

大门小品建筑属多项目综合性工程。本文作者从管理者的角度 ,通过对公司大门及附属工程施工质量控制的总结 ,说明了质量控制应贯穿于工程施工的全过程     

Sol-Gel Preparation of LaNiO3 and Its Physical and Chemical Properties

LaNiO3 was synthesized by sol-gel method in which lanthanum nitrate and nickel nitrate were used as start materials and citric acid was used as complex for gel formation.The precursor was dried and subsequently heated at elevated temperature to form the desired product.XRD analysis shows that pure LaNiO3 was synthesized.Electrical conductivity and electrochemical performance of the material were tested.The electrical conductivity decreases from 34.5that there are current peaks in the curve, which is the evidence of the electrochemical activity of LaNiO3.     

Anaerobic biodecolorization of textile reactive anthraquinone and phthalocyanine dyebaths under hypersaline conditions.

The biological decolorization of two industrial, spent textile reactive dyebaths was investigated using a suspended-growth, halophilic mixed culture fed with glucose. Dyebath I contained mainly Reactive Blue 19 (RB19), an anthraquinone dye, whereas dyebath II contained mainly Reactive Blue 21 (RB21), a phthalocyanine dye. Batch assays under anaerobic conditions with the two neutralized dyebaths resulted in 87 and 37% extent of decolorization for dyebaths I and II, respectively. The rate of glucose utilization and the extent of acetate production were impacted in the presence of each dyebath as compared to the control culture. However, dyebath decolorization occurred despite moderate culture inhibition. Reuse of a biologically renovated RB19-containing dyebath in the dyeing process resulted in reproducible but not identical cotton fabric shades as compared to a standard dyeing (i.e., control) using fresh water. This difference is attributed to a variable degree of RB19 aggregation during the dyeing process and is not related to the efficiency of the biodecolorization process. Further improvement of the redyeing efficiency will lead to the development of an in-plant, closed-loop decolorization system resulting in significant water conservation and minimization of textile pollutants such as salt and dyes.     

Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Hot-carrier reliability of 20V MOS transistors in 0.13 μm CMOS technology

This paper presents results of reliability investigation of 20 V N-Drift MOS transistor in 0.13 μm CMOS technology. Due to high performances required for CMOS applications, adding high voltage devices becomes a big challenge to guarantee the reliability criteria. In this context, new reliability approaches are needed. Safe Operating Area are defined for switch, V_ds limited and V_gs limited applications in order to improve circuit designs. For V_ds limited applications, deep doping dose effects in drift area are investigated in correlation to lifetime evaluations based on device parameter shifts under hot carrier stressing. To further determine the amount and locations of hot carriers injections, accurate 2D technological and electrical simulations are performed and permit to select the best compromise between performance and reliability for N-Drift MOS transistor.     

On Routh-Pade model reduction of interval systems

This paper discusses another generalization of the direct Routh table truncation method for interval systems. It is shown that the existing generalization of the direct Routh table truncation fails to produce a stable system, in contradiction to the equivalent result for fixed-coefficients systems. The present method guarantees a stable reduced order model for interval systems as well.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Quality-Assurance Technology in Japan

A survey of the state of SQA in Japan finds that the situation is much like, but slightly different than, that in the US.