An alternative blind feedforward symbol timing estimator using two samples per symbol

Recently, S.J. Lee proposed a blind feedforward symbol timing estimator that exhibits low computational complexity and requires only two samples per symbol (see IEEE Commun. Lett., vol.6, p.205-7, 2002). We analyze Lee's estimator rigorously by exploiting efficiently the cyclostationary statistics present in the received oversampled signal; its asymptotic (large sample) bias and mean-square error (MSE) are derived in closed-form expression. A new blind feedforward timing estimator that requires only two samples per symbol and presents the same computational complexity as Lee's estimator is proposed. It is shown that the proposed new estimator is asymptotically unbiased and exhibits smaller MSE than Lee's estimator. Computer simulations are presented to illustrate the performance of the proposed new estimator with respect to Lee's estimator and existing conventional estimators.     

Postbuckling analysis of plates on an elastic foundation by the boundary element method

The postbuckling behavior of plates on an elastic foundation is studied by using the boundary element method (BEM). A new fundamental solution of lateral deflection is derived through the resolution theory of a differential operator, and a set of boundary element formulae in incremental form is presented. By using these formulae, the BEM solution procedure becomes relatively simple. The results of a number of numerical examples are compared with existing solutions and good agreement is observed. It shows that the proposed method is effective for solving the postbuckling problems of plates with arbitrary shape and various boundary conditions.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

试谈高炉冷却壁的检漏及维护

高炉冷却壁的检漏及维护，是炼铁工作者十分关心的问题，本文针对邯钢高炉具体情况，探讨了高炉冷却壁漏水的原因，检漏方法，漏水冷却壁的维护及预防措施。     

时序电路逻辑初始化问题研究

讨论同步时序电路初始化问题,提出了一种基于电路存储元件逻辑定级和可控性分析的同步时序电路逻辑初始化方法。同时也给出了针对ISCAS89电路的一些实验结果。     

Cu－MnO_2同槽电解半工业试验研究

提出了Ｃｕ－ＭｎＯ＿２同槽电解的新工艺，在同一电解槽同时得到电铜和电解二氧化锰两种产品，该新工艺具有低电耗、低酸雾污染和低酸耗等优点．     

用φ20mm离心萃取器两步法制取高纯钇

本文研究了中钇富镧稀土的氧化物溶液在环烷酸中的萃取行为，测定了镧钇组成、温度变化与分离系数的关系；在Ｐ＿（５０７）体系中研究了ｐＨ值与分配比的关系；提出用环烷酸、Ｐ＿（５０７）两种萃取剂制备高纯钇的工艺流程。用８４台φ２０ｍｍ离心萃取器进行了一个月的台架试验，结果证明两种萃取剂有很好的互补性，在满足钇的纯度要求下有较高收率。离心萃取器具有易分相、体系存留量少、液流密闭性好等优点，它更适宜于粘度大、级数多、产品纯度要求高的体系。     

1.48μm掺饵光纤放大器泵源

采用Ｐ型ＩｎＰ衬底新月型结构制备了１．４８μｍ大功率激光器，该激光器与单模光纤耦合输出功率大于４０ｍＷ。     

具有初曲率板弯曲的边界元分析

由于具有初曲率板弯曲问题的控制微分方程较复杂，直接求解原问题基本解推导边界积分方程较为困难。本文通过引入等效荷载，将此问题的控制微分方程化成与普通板弯曲基本方程形式相同的微分方程，利用一般求解板弯曲问题的边界元法迭代求解，建立了分析具有初曲率板弯曲问题的边界元法。算例表明本方法理论准确、精度良好。     

流动微量量热法研究阴离子表面活性剂在油砂表面的吸附

用流动微量量热法研究了十二烷基硫酸钠(SDDS)和十二碳羧酸钠(SL)在克拉玛依油田九区和乌尔禾区油砂上的吸附,简要地计论了吸附机理。所得实验结果表明,SL 在油砂上的吸附强度比 SDDS 的要大,在相当低的浓度下即可迟到饱和吸附。