Rapid screening of DON contamination in whole wheat meals by Vis/NIR spectroscopy and computer vision coupling technology

This work intends to develop an online experimental system for screening of deoxynivalenol (DON) contamination in whole wheat meals by visible/near-infrared (Vis/NIR) spectroscopy and computer vision coupling technology. Spectral and image information of samples with various DON levels was collected at speed of 0.15 m s⁻¹ on a conveyor belt. The two-type data were then integrated and subjected to chemometric analysis. Discriminant analysis showed that samples could be classified by setting 1000 μg kg⁻¹ as the cut-off value. The best correct classified rate obtained in prediction was 93.55% based on fusion of spectral and image features, with reduced prediction uncertainty as compared to single feature. However, quantification of DON by quantitative analysis was not successful due to poor model performance. These results indicate that, although not accurate enough to provide conclusive result, this coupling technology could be adopted for rapid screening of DON contamination in cereals and feeds during processing.     

Use of heat-moisture treated maize starch to modify the properties of wheat flour and the quality of noodles

Waxy, normal and high-amylose maize starches were subjected to heat-moisture treatment (HMT) and then added to wheat flour (WF) in different ratios (1%, 5% and 10%). The properties of blends and their cooked noodles were studied to investigate the effects of HMT starches. The incorporation of HMT starch in WF led to an increase in swelling power, peak viscosity and breakdown and to a decrease in setback, thus inhibiting retrogradation, hence enhancing resultant noodle softness. Compared to the same addition ratio of native starch to WF, HMT starch led to higher tensile strength and extensibility in resultant noodles. WF with added HMT starch had higher resistant starch than with native starch. This study showed that addition of HMT maize starch has potential to bring nutritional benefits. However, it is necessary to select the proper blending ratio and amylose content of starch to add, in consideration of its effect on noodle quality.     

Enhanced photoreactivity of MOFs by intercalating interlayer bands via simultaneous ?NCO and ?SCu modification

Herein, we propose a novel method to enhance the photoreactivity of an MOF catalyst by grafting isocyanate bonds ( NCO) and sulfhydryl-complexed copper ( SCu) onto ZIF-8 (NIF-SCu). The grafting process intercalated interlayer bands between the conduction and valence bands of ZIF-8, thereby providing a “ladder” for facile electron transition. The extreme improvement in the photoreactivity of NIF-SCu could be attributed to the enhancement in light responses in the range of 350–450 nm by  NCO groups and the widening of the visible light range of the MOF by  SCu groups. The formation of staggered energy levels in NIF-SCu could also narrow the band gap, lower the resistance, and facilitate the transfer of photogenerated carriers, thereby generating electrons with strong reduction potential in the  SCu conduction band. This study provides a new strategy for improving or even endowing the photoactivity of environmental functional materials with wide bandgaps.     

Fluoride-mediately solvothermal synthesis and tunable photocatalytic selectivity of urchin-like ZrO2 hollow microspheres

Photocatalysts often show excellent performances on the basis of their surface state of exposed faces with high reactivity, but unfortunately surfaces of this type are usually concealed into the interior of crystals for their high surface energy. We report here a possibility that for fluorine-terminated surfaces of monoclinic ZrO₂, these higher-energy surfaces could be retained and exposed. Urchin-like ZrO₂ hollow microspheres (UZHS) composed of nanoribbons with exposed (010) facets are obtained through a fluoride mediately solvothermal method. We prove the stabilization effect of fluorine adsorption on (010) facets by density functional theory calculations. More interestingly, UZHS exhibit tunable photocatalytic selectivity in dye degradation. The fluorinated UZHS exhibit good performances both on decomposing Congo red (CR) and methylene blue, while the surface-modified UZHS by calcination only favor decomposition of CR.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Influence of geosynthetic reinforcement on the stability of an embankment with rigid columns embedded in an inclined underlying stratum

Incompressible dipping substrata are commonly encountered in engineering practice. Compared to horizontal underlying strata, the inclined underlying stratum increase the risk of collapse of embankments reinforced with columns because it weakens the restraint of the column base. The objective of this study is to investigate the effectiveness of geosynthetics on improving the embankment stability when the underlying stratum is inclined. The influence of geosynthetic tensile stiffness on the ultimate surcharge and failure mechanism is studied. A deep-seated failure with column tilting occurs when the geosynthetic tensile stiffness is low, whereas a lateral sliding occurs when the geosynthetic tensile stiffness is high. To illustrate the contribution of geosynthetics, the distribution of the lateral pressures acting on the columns is analyzed.     

Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Evaluation of bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) as cathode materials for solid oxide fuel cells

Bismuth doped La_2-xBi_xNiO_4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10^?6 and 14.2 × 10^?6 K^?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm², which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes.