MAGNETOTHERMAL CONVECTION OF POLYATOMIC GASES IN HOMOGENEOUS MAGNETIC FIELDS Part I: Theory

The theory of magnetothermal convection of gases in homogeneous magnetic fields is developed from magnetogas-dynamic theory. Application is made to nonionized paramagnetic and diamagnetic gases between parallel vertical plates. An additive contribution to the natural thermal convection heat transfer results from the temperature dependence of the magnetic permeability of the gas. The result may be expressed parametrically in a dimensionless magnctoconvection number, which characterizes the magnetothermal contribution to the total heat transfer just as the Grashof number characterizes the natural thermal contribution. For oxygen gas at low pressure the magnetothermal contribution is shown to be proportional to p ³ H ²(ΔT)² /ηT ⁵ where p is the gas pressure, H is the magnetic field strength, ΔT is the temperature difference between plates, η is the viscosity coefficient and T is the absolute temperature.     

A NEW TOOL FOR NUCLEATE BOILING RESEARCH

A new tool for the study of nucleate boiling heat transfer has been developed. Photographic etching was shown to be effective in the manufacture of copper lest surfaces containing precise arrays of artificial pits, with densities as high as 2742 pits/cm².

The pits were shallow segments of spheres, with depth: diameter ratios on the order of 0.1. Pit diameters were on the order of 0.003 cm. Data showed that the pits significantly affected the characteristic boiling curves and critical fluxes for the surfaces studied while boiling Freon 113 at one atmosphere pressure.

Photoetching can be used in the future to produce a wide variety of test surface textures or site arrays. Careful control of such surface conditions may well lead to a better understanding of the nucleate boiling phenomena.     

亚临界和超临界状态下甲苯-多环芳香烃体系的气液相平衡

The phase behaviors of toluene/polycyclic aromatic hydrocarbon mixture systems were investigated with a continuous-flow type apparatus at 573.2,598.2.623.2 and 648.2K,while the pressure changed from 1 tp 5 MPa,The pseudo-binary phase behaviors were predicted with the Peng-Robinson equation of state with interaction parameters between toluene and pseudo-components considered.The phase diagrams of the system have been classified following the category of phase boundary diagram models.The extraction selectivity and efficiency of toluene as a solvent was discussed by comparing with that of hexane .The prediction model for selectivity was also suggested.     

环氧树脂/碳化硅复合材料的热性能及韧性

采用碳化硅作为增强剂制备了环氧树脂/碳化硅复合材料,考察了复合材料的热学及力学性能。实验结果表明,碳化硅的添加使环氧树脂的玻璃化温度提高。当碳化硅添加质量分数为3%时,复合材料的韧性与纯环氧树脂相比提高了35%。     

Comparative Study of Tocopherol Contents and Fatty Acids Composition in Twenty Almond Cultivars of Afghanistan

Afghanistan is the fourth largest producer of almonds in the world producing 78 native and 6 imported cultivars. However, till date, there have been no comprehensive data on nutrient profiles of the native cultivars. Thus, in the present investigation, tocopherol contents and fatty acid composition from the kernels of 20 selected native almond cultivars of Afghanistan were analyzed. The ranges of variability for the studied nutrients were similar to those already reported for almonds grown in other countries, such as 47.8–66.1% of total lipids (fresh weight basis), 62.54–81.57% of oleic acid in the total lipids, and 139.1–355.0 μg/g α-tocopherol in kernels. With respect to cultivars, significantly (p < 0.05) high content of total lipids were recorded in ‘Belabai’ and ‘Sattarbai’ (Afghan grade), oleic acid in ‘Khairodini’ and of α-tocopherol in ‘Khairodini-161 Samangan’ and ‘Belabai’ cultivars. Kernels from these cultivars can be used for nutrient dense food formulations. Daily consumption of 50 g almonds is sufficient to meet the RDA of α-tocopherol (15 mg/day), considering the average 300 μg/g of α-tocopherol in Afghan almonds. Also, these nutrient rich cultivars can be used in almond breeding programs globally, to focus on improving kernel oil composition and nutrient contents.     

Influence of alloying elements on microstructure and microhardness of Mg-Sn-Zn-based alloys

The phase evolution in （88%-91%）Mg-8%Sn-l%Zn-X （X=A1, Mn and/or Ce） system was analyzed via CALPHAD method and simulations were used in precise selection of the chemical composition. The influence of the addition of different alloying elements such as A1, Mn and Ce on the microstructure and microhardness of Mg-8%Sn-l%Zn-based alloys was investigated. Combined addition of A1 and Mn shows features distinct from separate addition of A1 or Mn. Additions of l%AI and l%Mn to base alloy result in the formation of massive A1-Mn phase in a-Mg matrix grains. Addition of Ce element can refme the second eutectic precipitates and form intermetallic compounds with Sn. Fine rod-like Sn-Ce phase presents mainly on the grain boundaries and plays a role in inhibiting grain growth. The effects of alloying elements on Vickers microhardness and indentation size effect of base alloy were examined.     

Evaluation of microstructure and mechanical properties of Mg-xCe-0.5Zn alloys by nano-indentation

The microstructure and mechanical properties of Mg-xCe-0.5Zn(x=0.5,1.5,2.5,molar fraction,%) alloys were examined using a nano-indentation technique.The alloys were fabricated using a vacuum induction melting method under an argon atmosphere. The microstructures of Mg-xCe-0.5Zn alloys mainly consist ofα-Mg and eutectic Mg12Ce phase.The volume fraction and size of the eutectic Mg12Ce phase increase with increasing Ce contents.Nano-indentation test results show that the indentation hardness and elastic modulus of the eutectic Mg12Ce phase are higher than those of theα-Mg matrix.In addition,the mean indentation hardness and elastic modulus of the Mg-xCe-0.5Zn alloys increase with the Ce addition amount increasing.     

Weldability evaluation and tensile strength estimation model for aluminum alloy lap joint welding using hybrid system with laser and scanner head

Aluminum welding using a hybrid system with a laser and scanner welding head was performed under various welding conditions to verify the feasibility of applying an aluminum alloy to a car body.The experimental material was 5J32 aluminum alloy,and the laser power,welding speed,and laser incidence angle were used as the control variables.The weld bead shape and the tensile shear strength were evaluated in order to understand the aluminum lap joint weld characteristics.Analysis of variance (ANOVA) was conducted to identify the effect of the process variables on the tensile shear strength.Tensile strength estimation models using three different regression models were also suggested.The input variables were the laser power,welding speed,and laser incidence angle,and the output was the tensile shear strength.Among the models,the second-order polynomial estimation model had the best estimation performance,and the average error rate of this model was 0.058.     

Surface effects of hybrid vibration-assisted femtosecond laser system for micro-hole drilling of copper substrate

The ultrafast laser based hybrid machining system was studied and a novel approach was demonstrated to improve laser machining quality on metals by vibrating the optical objective lens with a low frequency (500 Hz) and various displacements (0-16.5 μm) during a femtosecond laser machining process.The laser used in this experiment is an amplified Ti:sapphire femtosecond (10-15 s) laser system that generates 100 femtosecond pulses having an energy of 3.5 mJ/pulse with a 5 kHz repetition rate at a central wavelength of 790 nm.It is found that both the wall surface finish of the machined structures and the aspect ratio obtained using the frequency vibration assisted laser machining are improved compared with those derived via laser machining without vibration assistance.     

Effect of pulse time on surface characteristics and corrosion resistance during pulse electrochemical polishing

Pulse electrochemical polishing (PECP) was used to improve the mechanical properties,such as surface roughness and corrosion resistance,of conductive metallic materials.PECP can provide a smooth,bright,reflective,and deburred surface that exhibits superior corrosion resistance.In this work,stainless steel was used as the anode,and copper was used as the cathode due to their low electrical resistances.The surface roughness of the PECP sample was measured by atomic force microscopy (AFM).A scanning electron microscope (SEM) was used to observe surface characteristics,and an Auger electron spectroscope (AES) was used to analyze the metallurgical composition and thickness of the passive film.The aim of this research was to compare the corrosion resistance rates of the unprocessed and PECP-processed stainless steel.