超细Al（OH）3的粒度控制研究

采用铝酸钠种子分解法制备超细Al（OH）3.用X射线衍射仪（XRD）表征了样品的晶相组成,用扫描电子显微镜（SEM）观察了样品的形貌,用激光粒度分析仪测定样品的粒度分布.研究了NaOH浓度、NaOH/Al（OH）3摩尔比,分解温度,分解时间、晶种率和搅拌速率等因素对Al（OH）3的粒度的影响.结果表明：NaOH浓度越高,分解温度越低,NaOH/Al（OH）3摩尔比越小,得到的Al（OH）3颗粒的粒度越小.试验条件为：NaOH浓度180 g/L,NaOH/Al（OH）3摩尔比1.15,分解温度40℃,分解时间26 h,晶种率8％,搅拌速率200 rpm时,氢氧化铝颗粒的平均粒度为2.89 μm.     

Electroless deposition of Ni on template of halloysite and its magnetic property

Halloysite template, a ceramic substrate, is of a hollow cylindric structure, on which the fine Pd nanoparticles are uniformly formed by the reduction of palldate chloride to initiate electroless deposition. The electroless deposition of Ni is catalyzed by the Pd particles, which results in a uniform layer of Ni-P alloy on halloysite. The alloy is of a nanocrystalline structure, of which the average diameter is about 6 nm. After being heat-treated at 400 ℃, it contains both Ni and Ni12P5 crystal, meanwhile, the Ni crystal gets larger with an average size of 51.9 nm.The content of phosphorous in the Ni layer has a great influence on crystal structure. The metallized halloysite has a higher inherent coercive force, and a much lower saturation magnetization in its as-plated state, while after heattreatment, the inherent coercive force decreases drastically. These magnetic properties have great relationship with the superparamagnetism of Ni nanocrystalline and the stress anisotropy in Ni layer.     

Phase transformation behavior in Al-Zn-Cu alloys by hammering

The 5Cu40Zn55Al and 15Cu20Zn65Al alloys were prepared in the AI-Zn-Cu system, There exist the metastable phases ε and θ in the two alloys after homogenization treatment and furnace cooling, respectively. It is shown that the particles are refined from 3 mm to less than 10 μm after hammering the two alloys but there are still metastable phases. This means that the phase constituents of the two alloys have no changes by the deformation, which is different from that by balling. The phase constituents are not changed at room temperature by hammering, which is dependent on the deformation mechanism of hammering.     

AD7794在高精度低功耗测量装置中的应用

采用AD7794,一种典型的仪用ADC,与超低功耗混合信号处理器MSP430F1611,构成了一个测量计量电路.实际使用表明,该电路具有低功耗、高精度和长期稳定性的特点;实测非线性度不大于10-3量级,能满足大多教工业测量计量的要求.     

On the model-based networked control for singularly perturbed systems

In this paper, the control of a two-time-scale plant, where the sensor is connected to a linear controller/actuator via a network is addressed. The slow and fast systems of singularly perturbed systems are used to produce an estimate of the plant state behavior between transmission times, by which one can reduce the usage of the network. The approximate solutions of the whole systems are derived and it is shown that the whole systems via the network control are generally asymptotically stable as long as their slow and fast systems are both stable. These results are also extended to the case of network delay.     

浅议视觉传达设计中的“空白”

空白,也称为"虚空间",指被其他要素包围的空间。空白部分运用的好,有时则会成为设计中最突出、最令人瞩目的部分。本文就针对空白在视觉设计中的一些作用做相关的探讨。     

基于WebGIS高速公路应急联动系统设计

随着高速公路路网建设的不断加快,车辆的逐年迅猛增长,原有零散的信息化技术辅助支持已远远满足不了对应急事件处置的需求,建设全方位及时有效的应急联动系统成为高速公路信息化建设重点.文中根据对高速公路基础业务数据和GIS数据的整合与共享进行分析研究,充分运用WehGIS技术、手机定位技术、无线视频监控技术等各种先进信息技术,在J2EE平台上利用MVC开发模式,采用B/S结构,并结合ArcGIS地理信息系统平台,探讨高速公路应急联动系统的设计及其具体实现.     

工作流引擎的模型应用分析

结合中小型企业的办公应用背景,深入研究了管理系统中工作流引擎所采用的工作流模型。并从工作流模型的逻辑关系出发,详细分析了组成工作流模型的三大部分（过程模型、组织模型和资源信息模型）的模型结构,由其提供工作流模型的基本功能。