En/Decoder for Spectral Phase-Coded OCDMA System Based on Amplitude Sampled FBG

A novel en/decoder for spectral phase-coded optical code-division multiple-access system based on amplitude sampled fiber Bragg grating (FBG) is proposed. Both equivalent chirp and equivalent phase shift are achieved by amplitude sampling. Compared with previous en/decoder based on step chirped FBG, it is easier to fabricate. The performance of the proposed en/decoder is verified by both numerical simulation and experimental demonstration.     

隧道工程施工中应注意的问题

通过对海南省东线高速公路大茅山隧道施工的全程监理,阐明了在施工中应重点注意的几个问题,在此基础上,总结出隧道工程质量监督中必须做到的几点,以确保隧道工程施工安全及工程质量.     

进一步降低钼精矿中铜、铅含量的生产实践

分析了钼精矿Cu、Pb含量高的主要原因 ,通过实施一系列措施 ,达到了降低钼精矿中Cu、Pb含量的目的     

Kinetics study of Ti[O(CH2)4OCHCH2]4 initiated ring‐opening polymerization of ε‐caprolactone by differential scanning calorimetry

Chemical shrinkage was used for the in situ measurement of the progressing chemical stabilization reactions and the influence of ozone during the stabilization of polyacrylonitrile. A method for evaluating the activation energy through the sensitivity temperature is presented. The calculated results show that the activation energies were 161.57 kJ/mol in air and 181.23 kJ/mol in ozone-enriched air. Therefore, the chemical reactions were postponed during stabilization in ozone-enriched air. Ozone seemed to act in three ways: first, ozone promoted the formation of the serious skin–core structure. Second, ozone accelerated the chemical reactions and shortened the stabilization time at lower heating rates. Third, ozone postponed the chemical reactions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

双柱塞砂浆泵中工作机构的设计和仿真研究

本文介绍了双柱塞砂浆泵的工作原理，根据机构替代原理建立起双柱塞砂浆泵工作机构的运动分析模型，然后在MatLab环境下，详细介绍了工作凸轮曲线的设计程序，利用计算机设计程序可以方便地分析工作缸活塞以及工作凸轮机构的位移、速度、加速度，利用SIMULINK仿真工具箱进行运动学仿真，为工作机构设计提供相应的理论分析依据。     

λ-MnO2的结构与电性能研究

采用酸处理LiMn2O4的方法来制备λ-MnO2，并用X-射线衍射(XRD)、扫描电子显微镜(SEM)和恒电流充放电测试等方法对所得λ-MnO2的结构和电性能进行了研究。研究结果表明，所得λ-MnO2具有尖晶石型结构，晶粒细小，形貌较规则，粒径分布均匀；以其为正极组装成Li／MnO2电池的放电比容量达到226mAh/g。     

尼龙6/改性双马来酰亚胺共混物的制备

将尼龙6与改性双马来酰亚胺熔融共混形成合金以提高其热稳定性能.用转矩流变仪考察了尼龙6/改性双马来酰亚胺共混体系熔融反应过程中的流变行为,用TG-DSC测试了共混物的热性能.结果表明:熔融共混时,2组分间的化学反应进行很快,改性双马来酰亚胺用量增加,共混物的熔融粘度增大,温度或转速升高,平衡转矩降低;改性双马来酰亚胺可明显改善尼龙6的高温热稳定性能,当尼龙6与改性双马来酰亚胺的质量比为20/1时,共混物在236-340℃温度范围内有很好的热稳定性.     

过程控制级模拟轧钢系统的研制及在热轧试车中的应用

宝钢集团上海第一钢铁有限公司(后面简称一钢)新建的不锈钢工程1780热轧项目中,为了能在较短周期内完成所有的应用软件开发与测试任务,特别研制了模拟轧钢功能。本论文主要阐述利用计算机的集成思想,结合热轧工艺,来开发模拟轧钢功能,以及利用模拟轧钢进行现场各种情况的模拟测试。     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

Matlab软件在分形几何上的应用

以Koch曲线和塞尔平斯基三角形为例,介绍了Ma tlab软件在分形几何方面,对不规则图形进行直观描绘的方法。