氟塑料—石墨板式换热器在高温强腐蚀换热工况中的应用

通过氟塑料－石墨板式换热器在化纤生产中高温强腐蚀换热工况中的实际应用，并与常规换热器的使用情况的对比分析，阐述了这种新型换热设备的特点。     

碳纳米管(CNT)场发射显示器的关键技术的研究

对碳纳米管阴极的制备以及场发射显示器的真空封装技术进行了研究.利用一种新的碳纳米管生长工艺制备出了具有优良场发射性能的碳纳米管阴极.并将这种直接生长的碳纳米管薄膜作为阴极,结合一种弹性封装工艺,开发了一种具有简单字符显示功能的场发射显示器.该显示器在较低的工作电压下就可获得高亮度的显示效果,并且器件的亮度与驱动电压成较好的线性关系,这将有利于未来的碳纳米管场发射显示器实现高亮度和多级灰度显示.器件的持续工作寿命测试已经超过5500小时,充分验证了碳纳米管作为场发射阴极的应用潜力.     

邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.     

Trends and variations in neonatal length of in-hospital stay in Canada

The objectives of this study were to evaluate the possible mechanisms involved in prolongation of bleeding time in pre-eclamptic patients receiving a magnesium sulfate infusion to prevent convulsions. Eighteen pre-eclamptic patients near term or at term (4 cases 33 to 35 weeks; the remainder > 36 weeks) were studied. Fifteen of them received magnesium sulfate infusion; 3 did not and served as controls. Bleeding time (modified Ivy method with Surgicutt), platelet count, platelet aggregation pattern, as well as serum arachidonic acid metabolites [thromboxane B2 (TxB2) and 6-Keto-prostaglandin F1 alpha (6-Keto-PGF1 alpha)] werde done on admission to the labor floor (before magnesium infusion) and repeated at discontinuation of the infusion, 12-24 hours postpartum; the controls received the second test 24 hours postpartum. Thirteen of 15 patients receiving magnesium sulfate had an increase in bleeding time from an average of 6 minutes 31 seconds to 11 minutes 56 seconds, an 82% rise (p < 0.004). In 2 there was a decrease. Among the 3 controls the averages were 6 minutes 38 seconds and 6 minutes 3 seconds. The total magnesium given ranged from 52.5 to 145 grams. Platelet counts averaged 251,000/mm3 (range 145,000-519,000). Platelet aggregation pattern done in 11 patients and was normal and unchanged after magnesium in 10 of the patients with increased bleeding time and one control. TxB2 and 6-Keto-PGF1 alpha levels did not change significantly either after magnesium administration (688 and 135 pgm/ml, to 654 and 117) or in controls (695 and 230 pgm/ml, to 445 and 225). Likewise, the ratio of these 2 substances did not change in either group (6.3 to 6.6, and 4.2 to 2.2). There was no correlation between duration of infusion or total magnesium given and directions of small changes observed. This study confirms a prior preliminary observation that magnesium sulfate infusion, as currently used to prevent eclamptic convulsions, induces a significant prolongation of bleeding time. This effect is mediated neither by changes in platelets count or aggregation pattern, nor by changing the level or ratios of serum arachidonic acid metabolites (TxB2 and 6-Keto-PGF1 alpha). Further studies are needed to clarify the mechanism of this clinically important observation of increased bleeding following magnesium sulfate infusion.     

提高柴油机缸盖内腔铸造质量的工艺措施

缸盖是柴油机上的重要零件之一。铸造毛坯不可避免地存在劈缝、内腔粘砂、粗糙、局部不通等内腔质量问题 ,从而影响缸盖串水冷却效果。本文介绍了一些工艺措施 ,较好地解决了这个问题。     

自动力套管补贴加固技术及其在B125井的应用

随着油田开发时间的延长，油水井井下套管的损坏将越来越严重，套管故障井将越来越多，为了恢复套损井生产，将套管损坏所造成的损失降到最低，在配套波纹管补贴，水动力补贴，爆炸补贴等专门修套技术的基础上，通过认真调查研究，又配套了操作方便简单，适用套管损坏类型广的自动力套管补贴加固技术，使各种套管变形，套管断错（错开没有位移或位移量不大时）、套管破裂，误射孔井段封堵，已射开水层封堵等修井作业的难度进一步降低，从而进一步提高了修复井综合开发经济效益。     

低温腐蚀及其防护技术

为了加热炉和锅炉的安全经济运行 ,分析了烟气余热回收中低温腐蚀的机理 ,提出了行之有效地解决和防止低温腐蚀的几种技术方法     

水溶性防氧化剂在SMT用印制板上的应用

水溶性的防氧化剂是一种有机可焊性保护剂。其方法是在印制板完全阻焊、字符层的印刷，并经电检之后，通过表面浸渍在裸铜的贴片位或通孔内形成一种耐热性的有机可焊性膜层。这种有机、可焊、耐热的膜层，膜厚可达0.3-0.5mm，其分解的温度可达约300℃，传统的印制板的热风整平法亦无法满足QFP愈来愈密集的需求，同时也无法满足SMD表面平整度的要求，更无法适应PCB薄型化生产。烷基苯并咪唑的OSP法能弥补这项缺陷，因而在PCB业乃至SMT产业中得到了广泛的应用。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

柳沟庄—窟窿山油藏储集层裂缝类型及特征

根据岩心描述、薄片观察、X－CT扫描以及钻井、测井等资料，研究了酒西盆地青西坳陷柳沟庄－窟窿山油藏裂缝性储集层的类型及特征，分析了控制裂缝发育的地质因素及裂缝对油气的控制作用，认为储集层裂缝有3种基本类型，即构造裂缝、构造熔蚀缝和饼状破裂，主要受构造应力场及构造位置等因素的控制。根据裂缝形态、充填特征及其相互关系，裂缝的形成主要有3个期次，其中喜马拉雅运动晚期形成的第三期理解缝对油气运移和聚集最有效。研究结果表明，裂缝是柳沟庄－窟窿山油藏主要的储集空间和控制油气富集的因素。