On a New Method for H2 -Based Decomposition

This note proposes a simple linear matrix inequality (LMI) system for the design of static precompensators to reduce the interactions of a multivariable system. The approach is based on minimizing the H₂ norm of a modified system and the LMIs are derived from the well known technique of pseudodiagonalisation. The approach is applied to two complex real-life benchmark problems with high levels of interaction. It is shown that its performance is significantly better than previously proposed LMI optimization techniques for designing static precompensators     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

An element-based displacement preconditioner for linear elasticity problems

Finite element analysis of problems in structural and geotechnical engineering results in linear systems where the unknowns are displacements and rotations at nodes. Although the solution of these systems can be carried out using either direct or iterative methods, in practice the matrices involved are usually very large and sparse (particularly for 3D problems) so an iterative approach is often advantageous in terms of both computational time and memory requirements. This memory saving can be further enhanced if the method used does not require assembly of the full coefficient matrix during the solution procedure. One disadvantage of iterative methods is the need to apply preconditioning to improve convergence. In this paper, we review a range of established element-based preconditioning methods for linear elastic problems and compare their performance with a new method based on preconditioning with element displacement components. This new method appears to offer a significant improvement in performance.     

On the credibility of manet simulations

Simulation is useful for evaluating protocol performance and operation. However, the lack of rigor with which it's applied threatens the credibility of the published research within the manet research community. Mobile ad hoc networks (manets) allow rapid deployment because they don't depend on a fixed infrastructure. Manet nodes can participate as the source, the destination, or an intermediate router. This flexibility is attractive for military applications, disaster-response situations, and academic environments where fixed net working infrastructures might not be available.     

On-line estimation of kinetic parameters in anaerobic digestion using observer-based estimators and multiwavelength fluorometry.

Observer-based estimators (OBE) were used for estimation of state variables and kinetic parameters in an anaerobic digestion (AD) process. A simplified first-order model with time-varying kinetic parameters was used to design an OBE for kinetic parameter estimation. This approach was validated on a laboratory-scale anaerobic reactor equipped with a multiwavelength fluorometer for on-line measurements of COD and VFA concentrations in the reactor effluent. The proposed estimators provide continuous adjustment of kinetic parameters and can be used for predictions of state variables between samples acquisition and during sensor failure.     

Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys: Part I. Tensile deformation

The effects of α and β phase interactions on the room-temperature tensile and creep deformation behavior of α + β titanium alloys with Widmanst?tten microstructures were studied using Ti-6.0 wt pct Mn and Ti-8.1 wt pct V as the model two-phase alloy systems. This article, Part I, deals with tensile deformation. It was found that when the α phase is present as thin (<10-μm) plates in the α + β alloys, significant twinning occurs. No significant twinning was observed in single-phase alloys with the same chemistry and similar grain size. Additionally, the β phase of Ti-8.1 V deforms by stress-induced hexagonal martensite (α′), while only twinning occurs in the single-phase β alloy with the same chemistry. Twinning in the α phase in association with stress-induced martensite (SIM) in the β phase was observed for the first time in a two-phase titanium alloy. This behavior is explained in terms of a number of factors including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.