On trading wavelengths with fibers: a cost-performance based study

We consider the effect of multiple fibers on wavelength division multiplexing networks without wavelength conversion. We study networks with dynamic wavelength routing and develop accurate analytical models to compare various possible options using single- and multiple-fiber networks. We use results of an analytical model and simulation-based studies to evaluate the blocking performance and cost of multifiber networks. The number of fibers required providing high performance in multifiber networks and their costs are compared. A case is made for using multiple fibers in each link with fewer wavelengths instead of using a single fiber with many wavelengths. In particular, we show that a network with four fibers per link and with four wavelengths on each fiber without any wavelength conversion on any node yields similar same performance as the networks with one fiber per link and 16 wavelengths per fiber on each link and with full wavelength conversion capability on all nodes. In addition, the multifiber network may also offer the cost advantage depending on the relative cost of components. We develop a parametric cost model to show that multiple fibers in each link are an attractive option. Finally, such multifiber networks also has fault tolerance, with respect to a single fiber failure, already built into the system.     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

Structural Changes Induced in Nonstoichiometric Titanium Carbide by High-Temperature Deformation

The microstructure evolution in nonstoichiometric titanium carbide is studied during high-temperature deformation at high strain rates and low strains (shock compression) and at slow strain rates and high strains (superplastic regime). The results demonstrate that high-temperature deformation in a broad range of strain rates offers a means of controlling the microstructure of titanium carbide. By varying deformation conditions, one can obtain materials differing in microstructure and chemical composition, in particular, with equilibrium and nonequilibrium microstructures. Accordingly, the physicochemical properties of such materials also differ.     

Characteristic Features of the Optimal Processing of the Results of Measurements in the Case of a Random Observation Function

An analysis is made of the characteristic features and problems of the optimal processing of the results of measurements in the case of a random observation function utilizing a nonlinear Kalman filter. A method is proposed for increasing the convergence domain of the filter with additional processing of measurements in the frequency domain.     

河床变形对水电站动力设备工作条件的影响

水电站运行过程中河床变形会使河底高程逐渐降低。从而导致下游流量特性曲线下降以及水电站水头增大。水头增大使水电站气蚀特性发生变化，导致动力设备的正常工作条件受到破坏。并对其运行安全性和效率造成不利影响。以卡马河的沃特金水电站为例，阐述了河床变形对水电站动力设备工作条件的影响。     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

Narrow-band correction of the residual amplitude modulation in frequency-modulation spectroscopy

We have developed a narrow-band controller in the MHz range, based on a field-programmable gate array. It is used to control the probe beam intensity in frequency-modulated spectroscopy experiments with an acoustooptic modulator. The residual amplitude modulation at the modulation frequency (2.5 MHz) is reduced by 50 dB. The first-harmonic detection of the signals is operated in saturation spectroscopy of I/sub 2/ at 514.5 nm and 501.7 nm. A reduction of the background noise and a large increase in the signal-to-noise ratio are obtained.