Foaming in Electric Arc Furnace—Part II: Foaming Visualization and Comparison with Plant Trials

The kinetics of slag foaming by limestone particles was studied at 1773?K (1500?°C) with the aid of an X-ray imaging system. Two models were implemented to describe the decrease in foam height with the time on the basis of the lowering of the average temperature and CaO shell formation during decomposition reaction. The energy impact of carbonate additions was studied on an industrial scale in a 100-ton electric arc furnace (EAF). It was found that, in the case of the addition of carbonates after the scrap is completely molten, the heat effects for limestone and dolomite (2255 and 2264?kJ/kg, respectively) were only 70?pct from theoretical values. Comparing these values with similar additions during the scrap melting stage shows that the energy requirements in the case of carbonate additions to steel bath are much smaller. It was found from the trial heats with dolomite addition to the steel bath that the partial substitution of lime by raw dolomite can be made without an increase in energy consumption.     

A simplified method for the evaluation of fatigue crack front shapes under mode I loading

Two-dimensional elastic or elasto-plastic models dominate the current fatigue crack growth assessment and life prediction procedures for plate components with through-the-thickness cracks. However, as demonstrated in many theoretical and experimental papers, the stress field near the crack tip is always three-dimensional and, as a result, the fatigue crack front is not straight. It is normally curved towards the plate faces. Over the past few years there were a number of very careful numerical studies focusing on the evaluation of fatigue crack front shapes. However, the application of the direct numerical techniques to fatigue phenomena is a very tedious and time consuming process and, sometimes, it is quite ambiguous. In the current paper we develop a simplified method for the evaluation of the front shapes of through-the-thickness fatigue cracks. Further, we validate the developed method against experimental results, investigate the influence of various parameters on the crack front shapes at stable (steady-state) propagation and analyse the differences in the results of fatigue crack growth evaluation obtained with two- and three-dimensional approaches.     

Optical and electrical characterization of a gold nanoparticle dispersion in a chiral liquid crystal matrix

We report on the effect of gold nanoparticle (Au NP) dispersion in a chiral nematic liquid crystal (LC). Polarized optical microscopy and X-ray diffraction measurements evidence the insurgence of an order change in the LC host. Moreover, a comparative analysis based on dielectric and voltammetric spectroscopies performed on pure LC and on Au NP-doped LC shows that Au NP’s presence besides affecting LC order influences its electric properties: ion conductivity results importantly reduced, and beyond a threshold value of the applied field electrophoresis phenomena are induced.     

Effect of P2O5 on the Structural and Magnetic Properties of Magnetite‐Based Glass‐Ceramics

The specific morphology and magnetic properties of magnetite‐based glass‐ceramics obtained by crystallization of Fe‐containing borosilicate glassmelts in the presence of P₂O₅ as nucleating agent are investigated. We found that the distribution of the tiny nanoparticles of magnetite determines the low temperature response to magnetic field. The observed effects are discussed with respect to the following factors: (1) the existence of a multimodal size distribution of the tiny grains as revealed by Mössbauer spectroscopy, magnetometry, and high‐resolution electron microscopy; (2) the existence of a disordered layer at the grain surface which is driven by field in a magnetically ordered state; and (3) the interplay between the relaxation mechanisms in different temperature ranges.     

Molecularly imprinted poly(acrylonitrile‐co‐acrylic acid) matrix with sclareol

There are presented results regarding a new set of molecularly imprinted polymers (MIPs) based on acrylonitrile:acrylic acid (AN:AA) copolymer matrix. As template, it was used sclareol, an important anticancer bioactive compound, never used before for molecular imprinting. An emerging and insufficient studied MIP preparation method, namely the phase inversion, was used to prepare 0.8 mm spherical sclareol MIPs (S‐MIPs). Three AN:AA copolymers, having the initial monomer ratios 90:10, 80:20, and 70:30, were synthesized by radical copolymerization in emulsion, without emulsifier. After that, each copolymer was dissolved in the presence of the template (sclareol) in dimethylformamide. The imprinting and the morphology of these new materials were analyzed by rheology, elemental analysis, infrared spectroscopy, size exclusion chromatography, thermogravimetric analysis, differential scanning calorimetry, batch rebinding tests, and Scatchard analysis. The conclusion was that the AN:AA‐80:20 matrix proved to be the optimized solution between high rigidity (given by the AN segments) and high affinity for the template (given by AA segments), the average imprinting factor for this system being 2.67. POLYM. ENG. SCI., 54:1484–1494, 2014. © 2013 Society of Plastics Engineers     

Positional‐Species Composition of Triacylglycerols from the Arils of Mature Euonymus Fruits

Positional‐species composition (PSC) of 1,2,3‐triacyl‐sn‐glycerols (TAG) from the arils of mature fruits of 13 species of Euonymus L. genus was established. The residues of six major fatty acids (FA), palmitic, stearic, hexadecenoic (H), octadecenoic (O), linoleic (L), and linolenic, were present in the TAG. PSC of TAG was determined by their partial lipase hydrolysis. By using hierarchical cluster and principal component analyses, it was definitely demonstrated that separate taxonomic units forming this genus were significantly distinguished as regards PSC of TAG. In particular, the Euonymus subgenus greatly exceeded the Kalonymus subgenus in both total content of L in TAG and in the rate of its incorporation into their mid‐position, while TAG of Kalonymus were marked by a prevalence of O‐TAG and sn‐2‐O isomers. Thus, these subgenera were significantly distinct in the rate of incorporation of O and L residues in the sn‐2 position of TAG molecules. Meanwhile, the TAG from the Euonymus section species were marked by an enhanced concentration of H and the incorporation of H in UUU TAG was much more active than in other TAG types. As for positional‐type composition of TAG, saturated FA were always virtually absent in the sn‐2 position of Euonymus aril TAG.     

Rapid fabrication of poly(ε‐caprolactone) nanofibers using needleless alternating current electrospinning

Poly(ε‐caprolactone) ( PCL) biopolymer nanofibers and micro‐fibers have been fabricated for the first time at the rates up to 14.0 g per hour using a needleless and collectorless alternating current electrospinning technique. By combining the ac‐voltage, “green” low toxicity glacial acetic acid (AA) as the solvent and sodium acetate (NaAc) as an additive, beadless PCL fibers with diameters tunable from 150 nm to 2000 nm, varying surface morphology and degree of self‐bundling are obtained. In this new approach, the addition of NaAc plays a crucial role in improving the spinnability of PCL solution and fiber morphology. NaAc reveals the concentration‐dependent effect on charge transfer and rheological properties of the PCL/AA precursor, which results in broader ranges of spinnable PCL concentrations and ac‐voltages suitable for rapid manufacturing of PCL‐based fibers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43232.     

Effects of equal‐channel,multiple‐angular extrusion on the physical and mechanical properties of glassy polymers

Through the examples of polycarbonate and poly(methyl acrylate), the evolution of the structure and properties of glassy polymers processed by equal‐channel multiple‐angular extrusion (ECMAE) were studied. It was demonstrated that ECMAE allowed the substantial improvement of the set of strain–strength characteristics of these materials, regardless of the direction of loading applied. With the use of the data from scanning electron microscopy, differential scanning calorimetry, and dilatometry, we found that the simultaneous growth in the strength, plasticity, and impact resistance was related to the formation of a net of biaxially oriented polymeric chains, the decrease in the free volume, and the reinforcement of intermolecular interaction. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42180.     

Manufacture and measurement of combinatorial libraries of dielectric ceramics: Part II. Dielectric measurements of Ba1−xSrxTiO3 libraries

Applying combinatorial methods to materials science offers the opportunity to accelerate the discovery of more efficient dielectric ceramics. High-throughput methods have the potential to investigate the effects of a wide range of dopants on the dielectric properties, and to optimise existing systems, encouraging the short innovation cycles that the communications technology industry requires. The London University Search Instrument (LUSI) is a fully automated, high-throughput combinatorial robot that has the potential capability to produce large numbers of sintered bulk ceramic samples with varying composition in 1 day, as combinatorial libraries on alumina substrates. Ba_1−xSr_xTiO₃ (BST) libraries were produced by LUSI as a proof-of-principle, with x = 0–1 in steps of 0.1, and fired to 1350 and 1400 °C for 1 h. Part I of this paper described the manufacture and physical characterisation of BST libraries, showing a regular change in composition with x across the libraries. In this second part, the dielectric properties of BST libraries produced by LUSI are assessed at frequencies between 100 Hz and 1 MHz, and at temperatures between 150 and 500 K. Local piezoelectric properties were also characterised by scanning probe microscope (SPM). All measurements showed evidence of a clear functional gradient varying with x across the library, with measured _r corresponding to expected values for BST.