Arthroscopic reduction and fixation of bony avulsion of the posterior cruciate ligament of the tibia

Bony avulsion fractures of the posterior cruciate ligament of the tibia have commonly been treated by open reduction and internal fixation using the posterior approach. However, this approach, using the prone position, makes it difficult to investigate and treat other combined injuries of the knee joint. We report a case of posterior cruciate ligament avulsion of the tibia that was arthroscopically reduced and firmly fixed with two cannulated screws. The posterior sag was absent after the operation and the result was excellent. By arthroscopy, we got rigid fixation of the avulsed fragment for early rehabilitation, and detection of a concomitant injury was also possible.     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

A new hybrid active power filter (APF) topology

In this paper, a new hybrid active power filter topology is presented. A higher-voltage, low-switching frequency insulated gate bipolar transistor (IGBT) inverter and a lower-voltage high-switching frequency metal oxide semiconductor field effect transistor (MOSFET) inverter are used in combination to achieve harmonic current compensation. The function of the IGBT inverter is to support utility fundamental voltage and to compensate for the fundamental reactive power. The MOSFET inverter fulfills the function of harmonic current compensation. To further reduce cost and to simplify control, the IGBT and MOSFET inverters share the same DC-link via a split capacitor bank. With this approach harmonics can be cancelled over a wide frequency range. Compared to the conventional APF topology, the proposed approach employs lower dc-link voltage and generates less noise. Simulation and experimental results show that the proposed active power filter topology is capable of compensating for the load harmonics     

冷媒充填机的PLC控制

介绍了冷媒充填机控制系统的组成和工作原理，着重叙述了西门子S7－200可编程控制器与触摸屏结合的控制方式，使系统的性能得到较大的提高。     

化肥厂合成气及重整氢真空变压吸附制取高纯度氢气

从设计、生产操作和经济效益3个方面阐述了以化肥厂合成气及重氢为原料，通过真空变压吸附（VPSA）装置制取高纯度氢的过程。工业应用结果表明，该制氢工艺是一项操作简便灵活，制氢费用较低的工艺路线。VPSA装置技术和设计上的特点能够保证大的操作弹性、高的产品氢纯度和较高的氢气回收率。在36％－51％的低限负荷下，通过适当调整吸附时间，可获得纯度99％的氢气产品，89％－92％的氢气回收率。     

Motivations for the San Fernando Valley Secession Movement: The Political Dynamics of Secession

I argue that the motivation for the San Fernando Valley secession movement can be explained as a desire for local control based on democratic ideals, but I emphasize that the movement is also motivated in part by the tangible benefits that accompany such autonomy. After a brief look at possible economic and racial motivations behind the secession movement, I look for a political divide between the city and the Valley, based on literature that has found political divisions between urban and suburban areas. Evidence of a political divide is mixed, but does indicate that the Valley lacks representation in comparison to the rest of the city. Valley residents may also fear increasing minority political power, which could erode the dominance of Valley whites at the polls. There is also evidence that those who favor secession are most dissatisfied with representation and most concerned with getting their fair share of services from the city, indicating a strong desire for more local control. Images of a smaller, more democratic government, and a more engaged local civic community are prime motivations in the Valley’s quest for autonomy, though the possibility of reduced taxes, land use control, and increased political power do offer secessionists clear substantive benefits in addition to more democratic goals.     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

An experimental study of heat transfer characteristics of a pair of longitudinal vortices using color capturing technique

The flow and heat transfer characteristics of a pair of embedded counter-rotating vortices are studied experimentally. In order to control the strength of longitudinal vortices, angle of attack of the vortex generators is varied from ±20° to ±45°, and the spacing between the vortex generators is 4 cm apart. The heat transfer measurements using thermo-chromatic liquid crystal are made to provide the local surface distributions of heat transfer coefficients. The following conclusions are obtained from the present experiment. For the common-flow-down cases, two maximum values in the local heat transfer distributions exist for the three angles of attack. With the common-flow-up cases, only one maximum value exists. The common-flow-down cases show better heat transfer characteristics than the common-flow-up cases.     

电脑提花圆机图案的设计与开发

应用当前景流行的图形设计软件Coredraw9.0和Photoshop5.0，设计针织面料T恤花型，进一步利用SCC4F-548型电脑提花圆机相配套的图形设计软件Aupaint处理，生成提花花型图案，为夏季T恤花型图案设计提供了一条简便快捷的设计方法和新的设计思路。