An improved code density test for the dynamic characterization offlash A/D converters

An improved code density test for flash A/D converters is proposed, revealing some dynamic phenomena (e.g., missing codes) hidden by the conventional approach. Formulas are reported for obtaining, from code density, effective noise estimates fully consistent with those provided by waveform analysis. Finally, it is shown that the variance of noise estimates obtained by time-domain analysis may be unacceptably large if the observation window is not properly chosen     

Development of an octocalcium phosphate cement

From previous studies it is known that alpha-tertiary calcium phosphate and dicalcium phosphate form a cement upon mixing with water. In this study this cement was optimized in terms of the milling of the constituents, their molar ratio, the amount of hydroxyapatite added and the water/powder ratio. The optimum Ca/P molar ratio of the cement mixture was 1.36±0.03. X-ray diffraction showed the reaction product to be octocalcium phosphate. Addition of precipitated hydroxypatite of over 3% diminished the final strength of the cement significantly. However, admixtures of only 2% of precipitated hydroxyapatite (a) kept the final compressive strength at 30±5 MPa after soaking in Ringers solution at 37°C, (b) diminished the initial setting time from 27.5 to 10 min and the final setting time from 65 to 40 min, (c) diminished the time in which the final strength was reached from 36 to less than 14 h. The tensile strength of this cement is 19±1% of its compressive strength. The optimum water/powder ratio as found in this study was 0.30 g/g.     

Comparison of two current modulation strategies for matrixconverters under unbalanced input voltage conditions

In this paper, the input current performance of matrix converters is analyzed, especially with reference to the operating conditions determined by unbalanced supply voltages. The space-vector modulation (SVM) technique is utilized to calculate the duty cycles of the active voltage vectors that must be applied, in each switching cycle period, in order to satisfy the input and output requirements. A detailed theoretical analysis of the input current harmonic content under unbalanced input voltage conditions is presented for two different current modulation strategies. On the basis of numerical simulations as well as measurements on a laboratory prototype setup, the strategies' performance are compared and the validity of the theoretical investigation confirmed. It is concluded that, when the input voltages are unbalanced to a significant extent, a dynamic input current modulation strategy has to be preferred, since a lower harmonic line current distortion will appear     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Relation between abrasion resistance and flexural strength of high volume fly ash concrete

In this paper, abrasion of high volume fly ash (HVFA) concretes made with 50% and 70% of cement replacement with fly ash was assessed in terms of its relation to flexural tensile strength. Comparisons were made between normal Portland cement (NPC) concrete and fly ash concrete. Comparisons were also made between fly ash concretes. Investigation results have shown that the abrasion resistance increased as flexural tensile strength increased. Analysis of the results showed that, for concrete with tensile strength of greater than 4–5 MPa, the abrasion resistance of HVFA concrete with 70% replacement with cement was found to be higher than that of counterpart control NPC concrete and concrete made with 50% fly ash. The comparison between the relation of abrasion to compressive strength and abrasion to flexural tensile strength made in terms of R² of the linear regression showed that a stronger relation existed between abrasion and flexural tensile strength than that of abrasion to compressive strength of the concrete studied.

---

Résumé L'étude a pour but d'estimer la relation entre la résistance à l'usure avec la résistance à la traction en flexion des bétons contenant de 50% et 70% de cendres volantes. On a comparé le béton pur au béton contenant des cendres volantes. Des comparaisons ont été faites également entre les différents bétons contenant des cendres volantes. Les resultats de la recherche ont montré que la résistance à l'usure augmente à mesure que la résistance à la traction en flexion de 4∼5 MPa ont une résistance à l'usure plus grande s'ils contienneint 70% de cendres volantes que s'ils étaient purs ou contenaient 50% de cendres volantes. La comparaison entre les relation de la résistance à l'usure en compression et de la résistance à l'usure en traction a été établie en termes de R² de la régression linéaire. On a prouvé qu'une relation plus forte a été obtenue entre la résistance à l'usure et la résistance à la traction en flexion par rapport à la résistance à l'usure en compression du béton étudié.

     

Propagation of flicker in electric power networks due to windenergy conversions systems

Wind energy conversion systems (WECS) produce fluctuating output power, which may cause voltage fluctuations and flicker. Flicker assessment in networks may be difficult since its evaluation requires long computing time and special procedures to calculate the flicker severity index, Pst. In this paper, a frequency domain method to study flicker propagation is presented. This method is based on propagation of frequency components from WECS output currents throughout the grid. In this way, a fast flicker analysis in a network of any size can be performed. Also, an algorithm for flicker measurement in the frequency domain, which allows Pst calculation, is proposed. Several study cases have been performed, and results have been compared with time domain simulations, showing good agreement between them     

Mechanism analysis of gate-induced drain leakage in off-state n-MOSFET

An analytical expression for both band-to-band and band-trap-band indirect tunnelings is used to study the gate-induced drain leakage (GIDL) current of MOSFETs measured before and after hot-carrier stress. The voltage and temperature dependence of GIDL are characterized. Both results show that interface traps situated near the midgap participate in the conduction of GIDL, and band-trap-band indirect tunneling could be the major mechanism. This is further supported by the fact that the percentage increase in GIDL induced by hot-carrier stress is about the same as the corresponding increase in interface-trap density. On the other hand, under low-field conditions, trap-assisted Poole–Frenkle emission dominates over tunneling for temperatures even well below room temperature.     

Ka-band solid-state pulsed Gunn oscillator and power combiner

GaAs Gunn diodes were fabricated for pulse source application at 8 mm wave band and operated with pulsewidths of 0.05 to 2.0 microseconds and duty cycles of 0.001 to 0.01. Peak pulse output power levels of 0.8–1.2W are achieved and the maximum available power is 1.6W with the highest efficiency of 6.5 percent. A simple and compact pulsed power combiner is also given in this paper.