北京市部分学校教室采光照明现状分析

近年来我国学生视力不良检出率居高不下,并且呈现明显上升趋势,已经到了极为严重的程度.学校教室的采光照明问题是保护学生视力健康的重要部分.2004年我国重新修订了国家标准〈建筑照明设计标准〉GB50034-2004.本文对北京市部分大中小学校进行采光照明的调查分析,结果显示,北京市学校教室采光照明问题十分严重,与国家标准要求差距很大,在被调查的39间教室中,窗地面积比达标率为20.5%,课桌面照度达标率为25.6%,黑板照度达标率为零.     

Gate and drain currents in off-state buried-type p-channel LDDMOSFETs

The buried-type p-channel LDD MOSFETs biased at high positive gate voltage exhibit novel characteristics: (1) the ratio of the drain to gate currents is about 1×10^-3 to 5×10^-3; and (2) the gate and drain currents both are functions of only the gate voltage minus the n-well bias. Such characteristics are addressed based on the formation of the surface n ⁺ inversion layer due to the punchthrough of the buried channel to the underlying shallow p-n junction. The measured gate current is due to the Fowler-Nordheim tunneling of electrons from this inversion layer surface and the holes generated within the high-field oxide constitute the drain current. The n⁺ inversion layer surface potential is found to be equal to the n-well bias plus 0.55 V. As a result, both the oxide field and the gate and drain currents are independent of drain voltage     

偏振模色散统计特性的研究

利用动态方程研究了偏振模色散矢量的统计特性 ,分别用统计系综和频率系综两种方法进行数值模拟。数值结果表明 ,统计系综和频率系综两种方法的结果一致。在大归一化距离条件下 ,均方根时延的平方随归一化距离线性变化 ;偏振模色散矢量的各个分量服从高斯分布 ,差分群时延服从麦克斯韦分布 ;偏振模色散矢量弥散于整个邦加球     

微重力落塔电磁悬吊、释放技术研究

论述了微重力落塔电磁悬吊、释放、提升机构的关键技术,电磁释放过程的特性分析以及微重力落塔实际试验的情况。分析说明:悬吊、释放性能的好坏决定了试验落舱的微重力水平,也是微重力落塔试验能否成功的关键技术。     

回归分析法简化钻爆设计

以某工程钻爆参数为例,阐述了在地下工程掘进施工中,应用回归分析法建立钻爆参数的相关模型,并利用此模型帮助建立某断面钻爆方案.     

倾斜水塔的爆破拆除

针对某部倾斜水塔的定向爆破拆除,从防止水塔倾倒偏移和筒体触地冲击地面对周围环境造成影响等不利情况,确定爆破方案和采取相应的防护措施.     

The effect of pack-aluminisation on the microstructure of MCrAlY and the performance of thermal barrier coatings

Plasma spraying and pack-aluminising processes were combined and applied to the nickel-base superalloy Mar-M247 to improve its cyclic oxidation resistance. The performance tests of duplex ZrO₂-8 wt.%Y₂O₃/MCrAlY thermal barrier coatings (TBCs) were conducted at 1050 °C, 1075 °C, 1100 °C, 1150 °C and 1200 °C. The results of the experiments in this study showed that TBC specimens with the aluminised MCrAlY bond coat exhibited higher cyclic lives (except for the Ni-22Cr-10Al-1Y bond coat), at all the temperatures tested, than specimens on which the bond coat was not aluminised. The microstructures of the Co-29Cr-6Al-1Y, Co-32Ni-21Cr-8Al-0.5Y and Ni-22Cr-10Al-1Y bond coats with or without aluminising treatment were examined in detail using a scanning electron microscope equipped with an electron probe microanalyzer.     

An efficient approach for calculating the dispersions of photonic-crystal fibers: design of the nearly zero ultra-flattened dispersion

A novel and efficient approach is proposed to calculate the dispersions of the guided modes of the photonic-crystal fibers (PCFs). Based on the vector boundary-element method (VBEM), the surface integral equations for the first and second derivatives of the propagation constants with respect to the wavelength are explicitly derived. Compared with the three-point finite-difference approach, which needs to solve and search three effective indexes near the interested wavelength, this approach can determine the dispersions of the PCFs by only solving one effective index at this wavelength based on the derived formulations. This novel approach saves over 60% computing time without losing the accuracy. Based on this approach, a novel four-ring PCF is designed by optimizing only three geometrical parameters to achieve the nearly zero ultra-flattened dispersion property. Compared with previously presented dispersion-flattened PCFs, the design procedure for the four-ring structure could be more efficient and easier because relatively lesser parameters need to be optimized.     

60Co辐照预处理对苹果片脱水特性和品质的影响

进行了不同辐照剂量、热风温度、切片厚度对苹果脱水速率及品质的影响试验,结果表明该三因子影响苹果片的脱水速率和外观质量.辐照剂量增加,热风温度增高,脱水速率高,VC含量和复水比下降.辐照剂量、热风温度、切片厚度三因素对脱水速率和干制品的外观质量、VC含量、复水比等四指标大都呈显著影响.     

A Study of AlN Films Prepared by Arc Ion Plating

Hexagonal AlN films have been obtained by arc ion plating at different negative biases ,X-ray diffraction and scanning electron microscopy results show that AlN films with smooth surfaces and (002) preferred orientation are obtained at low biases ,whereas those with coarse surfaces and (100) preferred orientation are obtained at high biases,The formation mechanism of AlN is analyzed and the experiment results are discussed,The effect of bias on adhesion strength has also been examined.