Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Preparation of vanadyl porphyrin complexes from a metal-porphyrin petroleum concentrate and study of their catalytic activity

A mixture of vanadyl porphyrin complexes was obtained from a metal-porphyrin concentrate (MPC) isolated from crude petroleum by selective extraction. The petroleum MPC was subjected to demetallization and the subsequent introduction of the vanadyl cation into the porphyrin ring. It was shown that the mixture of vanadyl-porphyrin complexes obtained from MPC catalyzes the cyclohexene epoxidation reaction. On the basis of experimental data, it was assumed that the mechanism of olefin oxygenation in the presence of vanadyl porphyrin complexes is similar to the mechanism of the Prilezhaev epoxidation reaction of unsaturated compounds.     

Nanolayered lightweight flexible shields with multidirectional optical transparency

New nanolayered coatings are designed and deposited on flexible plastic substrate having the thickness of 100 /spl mu/m, in order to realize lightweight ultrathin transparent shielding foils. The structure of the coating is optimized considering three figures of merit: the average transmittance in the visible range for normal incidence, the normalized average transmittance for oblique incidence at 550 nm, and the transmittance quality factor. The nanotechnology exploited for the deposition of the transparent metals is the dual ion beam sputtering. Tests of durability, optical transmission, and shielding effectiveness demonstrate that the film has a high adhesion under mechanical solicitation, high resistance against aging, peak transmittance in the visible range higher than 70%, omnidirectional properties in the range 0/spl deg/-60/spl deg/, and shielding effectiveness of 40 dB up to 6 GHz.     

Determination of precompression and compression force levels to minimize tablet friability using simplex

Pilot simplex experiments for improving the tablet strength of three aspirin tablet formulations based on precompression and compression forces were presented. As each simplex moved towards the direction of the optimum, the friability was being minimized and the crushing strength was concomittantly being maximized. Because it followed a systematic direction, simplex process would locate a local optimum rapidly. The appropriate levels of precompression and compression forces that produced tablets with the desired strength were attained in five trials. By contrast, random search for this force combination required at least ten trials. Simplex technique is a cost and time effective means for determining the precompression and compression forces that will reduce the friability or increase the hardness of a tablet formulation. Results appeared to also indicate that crushing strength might be a more reliable measure of tablet strength than friability.     

Experimental abatement data of underflow baffles for removal of floatables in the CSOs of the Greater Montréal (Canada) area.

Underflow baffles have gained in popularity over the years as a viable mean to intercept floatables in Combined Sewer Overflows (CSOs). This choice was mainly justified by the extremely low capital cost (CAPEX) and operational cost (OPEX) of this solution, although the efficiency of underflow baffles has never been clearly proven. The only similar application to underflow baffles are scum boards in grit chambers and clarifier. However, the flow conditions at CSOs vary considerably from those in grit chambers and clarifier. For this reason, review of the behavior of floatables in a rapid flow is paramount. Only then can comprehensive design criteria for underflow baffles and overflow chambers be suggested. Pilot scale tests, performed in a 17 metres long basin at various flowrates, had already shown that a critical horizontal velocity for floatables (Vcr) may develop in the overflow chambers. In this follow up study, the fate of intercepted floatables was investigated. It appears from this latest data that permanent capture of floatables decreases rapidly with an increase in the horizontal velocity of the flow, no matter what the baffle depth. Baffle depth increases capture at lower velocities (0.17 m/s) but become irrelevant at higher velocities (0.61 m/s). This data suggests that capture efficiency of existing underflow baffles in overflow chambers can be, at best, very low whenever the horizontal velocity increases above 0.30 m/s or 1 ft/s.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.