铸造湿型小件缺陷产生的原因与控制

通过对铸造湿型小件产品缺陷典型实例的原因分析，从型砂的选择及配制、造型工艺、浇注工艺等方面提出控制缺陷产生的工艺方法。     

Ultrasonic thin-walled tube wave structure for sensing devices

Theoretical and experimental investigations of thin-walled tube acoustic wave devices for gravimetric sensing applications are presented. Integrated sensor configurations have been demonstrated by employing a sol-gel processed thin piezoelectric lead zirconate titanate (PZT) film. This was coated coaxially on stainless steel tubes and interdigital transducers (IDT) fabricated as the transmitter and receiver on the curved tube surfaces. We have observed tube waves along both the axial and circumferential directions between 1 and 6.6 MHz. We have also analyzed the mass sensitivities of different modes propagating along the tubes and shown that high mass sensitivity can be achieved by keeping the tube wall thin     

大面积硅锂漂移探测器制备及其性能

制备了大面积硅锂漂移探测器,其性能为:探测器的灵敏面积123.6 cm~2;灵敏层深度2 mm;在室温和300 V反向偏压的工作条件下漏电流小于20 μA;对~(241)Am 5.486 MeV α粒子的能量分辨(FWHM)为77.67 keV。     

Gain optimization for Yagi-Uda arrays

The author presents a personal account of the search for a design procedure for Yagi-Uda antenna arrays yielding a maximum gain, or directivity if element losses are neglected. Results on current distributions in the array are briefly reviewed. The analytical approach used to achieve gain optimization by means spacing and length perturbations is sketched. By using both spacing and length perturbations, it was possible to find the optimized array analytically in a systematic way, some examples having gain increases of nearly 80%. The effects of finite dipole radius and mutual coupling were included in the theoretical treatment     

Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

提高E^2PROM中NMOS管源漏穿通电压的实验研究

为了提高Ｅ＾２ＰＲＯＭ中Ｎ管源漏穿通电压，用实验的方法对制造工艺进行了研究。结果表明，高能量注入是提高ＶＰＴ的有效手段，但受到ｐｎ结击穿的限制，只适用于低区短沟Ｎ管；ＤＤＤ工艺大幅度高ＶＰＴ，但ｐｎ结击穿电压低于２０Ｖ，不能应用于高压ＭＯＳ管；采用适量的防穿通注入和适当增大沟道长度为最理想的工艺途径。     

双能X射线骨密度仪测定技术研究

以Ｌｕｎａｒ公司ＤＰＸ－Ｌ型双能Ｘ射线骨密度仪为例，研究引起测量误差的主要因素并提出质控措施。用自检模块、腰椎体膜评定仪器的体外测量精度好于１％。对１０位志愿者重复２次测量，体内精度对腰椎，ＭＰＤ（平均百分差）为０．４６，ＣＶ（变异系数）为０．７５；对股骨颈，ＭＰＤ为１．２６、ＣＶ为０．４７；Ｗａｒｄ’ｓ三角区ＭＰＤ为２．０１、ＣＶ为１．１４；大转子ＭＰＤ为１．６６、ＣＶ为０．７２。扫描图像由２位     

卤化银探测器及其某些特性

文中简述了卤化银(主要是溴化银)单晶片的某些特性,氯化银单晶片与此大致相似。作为低温晶体探测器,对~(241)Am-α放射源,分辨率为17%。卤化银晶片是固体电解质,只有Ag离子对输出电信号有贡献,有显著的极化现象。在液氮槽内溴化银晶片的电导率在几个数量级内成为可控的,由在室温下外加偏置电压大小所引起的分解状态下的初始电流决定。     

Cell cycle regulation of the Saccharomyces cerevisiae polo-like kinase cdc5p

Progression through and completion of mitosis require the actions of the evolutionarily conserved Polo kinase. We have determined that the levels of Cdc5p, a Saccharomyces cerevisiae member of the Polo family of mitotic kinases, are cell cycle regulated. Cdc5p accumulates in the nuclei of G2/M-phase cells, and its levels decline dramatically as cells progress through anaphase and begin telophase. We report that Cdc5p levels are sensitive to mutations in key components of the anaphase-promoting complex (APC). We have determined that Cdc5p-associated kinase activity is restricted to G2/M and that this activity is posttranslationally regulated. These results further link the actions of the APC to the completion of mitosis and suggest possible roles for Cdc5p during progression through and completion of mitosis.