Electrical properties of La0.6Sr0.4Co1-yFeyO3 cathode material

The electrical properties of La0.6Sr0.4Co1-yFeyO3 （LSCF, y=0-1.0） cathode materials were measured by DC four probes, X-ray photo-electron spectrum （XPS） was also introduced to determine the chemical state of Co, F.e ions in LSCF. It is found that the electrical conductivity of each sample has a maximum value with increasing temperature. XPS analysis shows that Co ion has three different chemical states, corresponding to two with Fe ion. The analyses indicates that the small-polaron hopping mechanism dominates the electron conduction at low temperature, while at high temperature, the three factors such as the thermally activated disproportionation of Co^3＋ ions into Co^2＋ and Co^4＋ pairs, the ionic compensation of oxygen vacancies formed at high temperatures, and Fe^4＋ ions charge compensation preferential to Co^4＋, all contribute to electrical conduction.     

定、转子冲片级进模维护要领及常见故障的排除

通过对电机定、转子片级进冲模结构形式的分类、凸模、凹模常见的固定方式的介绍，阐述了电机定、转子片级进冲模模具在日常使用中的维护和保养要领。重点介绍了凸模、凹模的更换程序，卸料板的安装程序，以及模具在使用中常见故障原因的分析和排除方法。     

超声及电磁场对铝合金熔体影响的数值模拟及试验研究

针对铝合金熔体的超声及电磁搅拌处理过程,创建了超声场、电磁场、流场和温度场的数学模型,并采用COMSOL Multiphysics软件求解模型,得到了超声场、电磁场和超声/电磁复合场对铝合金熔体内流场和温度场的分布规律,并通过试验对模拟结果进行了验证。结果表明,增加超声功率使得声压幅值和流场的流动速率均随之增加,同时会使熔体的温度梯度逐渐减小;施加电磁场后产生的电磁搅拌改变了熔体的流动方向且使熔体的流动速率显著增大,这对熔体的温度分布产生了较大影响;在超声和电磁复合场下,电磁场比超声场对熔体流场和温度场的影响更大,且占主导地位。数值模拟结果和试验结果符合较好。     

Superplasticity of fine-grained 7475 Al alloy and a proposed new deformation mechanism

A study has been made to investigate the superplastic deformation mechanisms of 7475 Al alloy in relation to the variation of grain size ranging between 5.5 μm and 13 μm. The strain-rate sensitivity (m) was increased with decreasing grain size in the superplastic deformation regime. Microstructural investigation after tension tests revealed that the dispersoid free zones were produced mostly at the grain boundaries normal to the tensile direction. A new model for describing the deformation behavior of the 7475 Al alloy has been proposed based on the assumption that the grain boundary sliding was accommodated by both diffusional flow and slip. This new model well predicts many aspects of experimental results.     

The form error prediction in side wall machining considering tool deflection

In this research, an effective method for the form error prediction in side wall machining with a flat end mill is suggested. The form error is predicted directly from the tool deflection without surface generation by cutting edge locus with time simulation. The developed model can predict the surface form error accurately about 300 times faster than the previous method. Cutting forces and tool deflection are calculated considering tool geometry, tool setting error and machine tool stiffness. The characteristics and the difference of generated surface shape in up milling and down milling are discussed. The usefulness of the presented method is verified from a set of experiments under various cutting conditions generally used in die and mold manufacturing. This study contributes to real time surface shape estimation and cutting process planning for the improvement of form accuracy.     

中厚板在线30通道超声波探伤方法及应用

介绍了柳钢公司在生产锅炉板、压力容器板过程中，曾试用了６种探伤方法；而研制的３０通道在线超声波探伤法不仅可满足国家标准要求，而且能适应生产节奏，并具有快速、准确、简便的特点。     

Microstructure of reactive sintered Al bonded Si3N4-SiC ceramics

Aluminium nitride-silicon nitride-silicon carbide （AIN-Si3N4-SiC） composite ceramics were prepared to increase the bending strength and improve the phase structure of Si3N4-based ceramics. The ceramics were made by reactive sintering in N2 atmosphere at 1 360 ℃, using Al as sintering additive. The phase composing of ceramics was identified with an X-ray diffractometer and the microstructure of the materials was studied by scanning electron microscopy. The results indicate that the phase structure is affected remarkably and the interface modality is changed. The interface between Si3N4 and SiC becomes blurry and that between SiC and AlN matches more better at the same time. But the liquid-phase appears during the reactive sintering along with the addition of AI by which the melting point of Si is decreased. The appearance of liquid Si decreases the bending strength of the ceramics. Lower temperature nitrification technic was introduced to avoid the appearance of liquid-phase Si. The optimum addition of Al was investigated by XRD and SEM analysis in order to obtain the maximal bending strength of materials.     

用于交流自动埋弧焊机的SCR—D调节系统

本文阐述了用SCR-D调节系统代替F-D调节系统的交流自动埋弧焊机的工作原理和电路分析,同时也对该焊机自动引弧提出见解。     

基于速龙码的WSNs传输功率控制重编程协议

为了降低节点能耗,提高能量的利用率,提出了一种高效节能的基于速龙码（ RC）的传输功率控制（ RC-TPC）重编程协议。该协议分两个阶段完成数据传输,第一阶段各个节点更新自己的位置信息,形成最优化的拓扑结构。进入第二阶段后,根据优化的拓扑结构通过调整发送节点的传输功率和中继节点的累计选择次数,Sink节点选择适当的中继节点,使中继节点的传输功率和RC的开销达到最优化。此外,RC的编码方式使传输数据包发生的错误概率更小,减少了重编程过程中的冗余以保证网络负载的均匀分布,有效地实现了高效节能,从而提高整个网络的生存周期。理论分析与实验结果表明：与MNP协议和ATPC协议相比,RC-TPC协议用于传输的平均能量消耗降低17.2%。